HPE ProLiant DL360p Gen8 Parts

HPE ProLiant DL360p Gen8 Parts

HPE ProLiant DL360p Gen8 Parts

Restore or upgrade your HPE ProLiant DL360p Gen8 server with compatible parts designed for enterprise performance and long-term reliability. This 1U rackmount platform supports Intel Xeon E5 processors and is ideal for virtualization, databases, and general-purpose workloads.

Available DL360p Gen8 Parts:

  • Memory: DDR3 ECC RDIMM and LRDIMM modules
  • Drives: SAS and SATA SSDs and HDDs
  • Storage Controllers: HPE Smart Array RAID cards and HBAs
  • Networking: PCIe Ethernet adapters
  • Power Supplies: Hot-plug PSUs in 460W, 750W, and 1200W
  • Processors: Intel Xeon E5-2600 and E5-2600 v2 CPUs

Looking for a specific DL360p Gen8 part? Browse the subcategories below or reach out for expert assistance.

Memory

NOTE: HPE memory from previous generation servers are not qualified or warranted with this HPE ProLiant Server. HPE SmartMemory is required to realize the memory performance improvements and enhanced functionality listed in this document for Gen8.
NOTE: LRDIMM, RDIMM, and UDIMM, and HDIMMs are all distinct memory technologies and cannot be mixed within a server. The majority of ProLiant Gen8 servers support LRDIMM, RDIMM and UDIMMs.

E5-2600 v2 series Memory

Registered DIMMs (RDIMMs)

Unbuffered with ECC DIMMs (UDIMMs)

Load Reduced DIMMs (LRDIMMs)

NOTE: The following memory is supported by the E5-2600 v2 series Processors.

E5-2600 (v1) series Memory

Registered DIMMs (RDIMMs)

Unbuffered with ECC DIMMs (UDIMMs)

Load Reduced DIMMs (LRDIMMs)

NOTE: The following memory is supported by the E5-2600 series Processors.

Drives

NOTE: The HPE ProLiant DL360p Gen8 Smart Storage solutions are equipped with entirely re-designed Small Form Factor (SFF 2.5 in) and Large Form Factor (LFF 3.5 in) hot plug carriers for HPE Qualified Hard Drives and Solid State Drives. These new carriers provide status and activity indicators as well as caution indicators for 'Do Not Remove'.
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.

Hard Disk Drives

12G SAS Hot Plug with SmartDrive SFF 2.5in Enterprise HDD

12G SAS Hot Plug SmartDrive LFF 3.5in Converter Enterprise HDD

12G SAS Hot Plug SFF 2.5in SC 512e HDD

6G SAS Hot Plug with SmartDrive SFF 2.5in Enterprise HDD

6G SAS Hot Plug SmartDrive SFF 2.5in Midline HDD

6G SAS Hot Plug SmartDrive LFF 3.5in Midline HDD

6G SATA Hot Plug with SmartDrive SFF 2.5in Midline HDD

6G SATA Hot Plug with SmartDrive LFF 3.5in Midline HDD

6G SATA Hot Plug SFF 2.5in SC 512e HDD

6G SATA Hot Plug LFF 3.5in Midline 512e HDD

6G SATA Hot Plug LFF 3.5in SC 512e Performance HDD

12G SAS Hot Plug SFF 2.5in Enterprise HDD

12G SAS Hot Plug LFF 3.5in Midline 512e HDD

12G SAS Hot Plug LFF 3.5in SC 512e Performance HDD

Solid State Drives

6G SATA 2.5in WI-PLP SCC SSD

6G SATA 2.5in MU-PLP SCC SSD

6G SATA 2.5in RI-PLP SCC SSD

6G SATA 2.5in WI-PLP SC SSD

6G SATA 2.5in MU-PLP SC SSD

6G SATA 2.5in RI-PLP SC SSD

12G SAS Hot Plug Value Endurance SFF 2.5in Enterprise Value SSD

6G SATA Value Endurance Hot Plug LFF 3.5in Enterprise Boot SSD

12G SAS Mainstream Endurance Hot Plug SFF 2.5in Enterprise Mainstream H2 SSD

12G SAS Hot Plug SFF 2.5in SC Read/Write Intensive SSD

6G SATA Value Endurance Hot Plug SFF 2.5in Enterprise Boot SSD

6G SATA Value Endurance Hot Plug LFF 3.5in Enterprise Boot SSD

6G SATA Hot Plug Value Endurance LFF 3.5in Converter Enterprise Value M1 SSD

6G SATA Hot Plug Value Endurance LFF 3.5in Converter Enterprise Value G1 SSD

6G SATA Hot Plug Value Endurance SFF 2.5in Enterprise Value G1 SSD

6G SATA Value Endurance Hot Plug SFF 2.5in Enterprise Value SSD

6G SATA Value Endurance Hot Plug LFF 3.5in Enterprise Value SSD

6G SATA Hot Plug Light Endurance SFF 2.5in Enterprise Light G1 SSD

6G SATA Hot Plug Light Endurance LFF 3.5in Enterprise Light G1 SSD

6G SATA Value Endurance Hot Plug SFF 2.5in Enterprise Value M1 SSD

6G SATA Mainstream Endurance Hot Plug SFF 2.5in Enterprise Mainstream SSD

6G SATA Mainstream Endurance Hot Plug LFF 3.5in Enterprise Mainstream SSD

6G SATA Hot Plug SFF 2.5in SC Read Intensive SSD

6G SATA Hot Plug LFF 3.5in SC Read Intensive SSD

Hard Drive Kits

NOTE: All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives ordered with the server.

Hard Drive Cables

HPE DL38x/DL360 Gen8 Embedded SATA Cable Kit thumb
NOTE: This cable is only required to connect a single SATA drive to the embedded Intel SATA controller. The P420i controller is not used in this configuration and should be disabled via RBSU to save power.
$136
$93.00

Networking

Gigabit Ethernet Adapters

10 Gigabit Ethernet Adapters

NOTE: A minimum of two Gigabytes (2 GB) of server memory is required per each adapter.
NOTE: Direct Attach Cable (DAC) for copper environments or fiber transceivers and cables for fiber-optic environments must be purchased separately. See cables/options below.

FlexibleLOM Adapters

Secure Encryption

HPE Secure Encryption No Media Flexible License per Drive thumb
NOTE: HPE Secure Encryption is supported on the HPE Smart Array P731m and the P230i as an option. HPE Secure Encryption licensing is based on the number of physical drives requiring encryption.

InfiniBand

HPE Infiniband FDR/Ethernet 10Gb/40Gb 2-port 544QSFP Adapter thumb
NOTE: For the following two InfiniBand Adapters, only 1 FlexibleLOM can be added to the server, which is selected in Step 2 for the 'Configuration Information - Factory Integrated Models' section. These two options are for upgrade or change from original configuration.
NOTE: FLR Indicates new HPE FlexibleLOM Adapter series.
$128
$95.00
HPE Infiniband QDR/Ethernet 10Gb 2-port 544FLR-QSFP Adapter thumb
NOTE: 10Gb Ethernet requires the use of the QSFP to SFP+ adapter P/N 655874-B21.
$70
$49.00

Power Supplies

NOTE: Mixing of power supplies in the same server is not supported. All power supplies inside a server must be exactly the same model. Mixing Gold, Platinum, and Platinum Plus certified power supplies is not supported.
NOTE: Prior to making a power supply selection it is highly recommended that the HPE Power Advisor is run to determine the right size power supply for your server configuration. The HPE Power Advisor is located at: (link)

HPE Common Slot Titanium Power Supply Kits

NOTE: 96% efficiency with support for HPE Power Discovery Services.

HPE Common Slot Platinum Plus Power Supply Kits

HPE Common Slot Gold Power Supplies

NOTE: The following Power Supplies offer up to 92% efficiency.

HPE Common Slot -48VDC Power Supplies

NOTE: The following Power Supplies offer 92% Efficiency.
HPE 750W Common Slot -48VDC Hot Plug Power Supply Kit thumb
NOTE: The HPE 750W Common Slot -48VDC power supply does not ship with a power cable. It has been designed with a terminal block connection allowing for custom design of power cords by the user.
$488
$399.00

HPE Common Slot 277VAC Power Supplies

Storage Controllers

Smart Array Guide

SAS Controllers

Optional Upgrades

Host Bus Adapters

HPE H222 Host Bus Adapter thumb
NOTE: A quantity of 1 HPE Mini SAS Str to Left 33in Cable Assy (662899-B21) is required for proper connectivity.
$388
$266.00

SCSI HBA

Rack Options

HPE LCD8500 1U Rackmount Console Kit Models

HPE LCD8500 1U Rackmount Console Kit Options

HPE Location Discovery Services

HPE USB Keyboard and Mouse

HPE Server Console Switches

HPE Server Console Switch G2 with Virtual Media & CAC

HPE 1x4 USB/PS2 KVM Console Switch

Rail Kits

NOTE: Gen8 rail kits have changed significantly from prior generation rail kits. Please take a moment to review the installation documentation that comes with the server to help you with the installation of your Gen8 server.
NOTE: Rail kits are optional for Gen8 and are no longer included standard with the server. Customers have the option to purchase their server without a rail kit.
Caution: HPE recommends that a minimum of two people are required for all Rack Server installations. Please refer to your installation instructions for proper tools and number of people to use for any installation.
HPE 1U Small Form Factor Easy Install Rail Kit thumb
NOTE: For SFF models.
NOTE: Kit contains full extension rails which do allow for in rack serviceability. After the rails are installed the server is aligned with the rails and slid into the rack. The HPE 1U Easy Install Cable Management Arm is optional.
$243
$176.00
Caution: HPE recommends that a minimum of two people are required for all Rack Server installations. Please refer to your installation instructions for proper tools and number of people to use for any installation.
HPE 1U Cable Management Arm for Easy Install Rail Kit thumb
NOTE: Supports Easy Install rail kits only
$151
$108.00
HPE 1U Small Form Factor Ball Bearing Rail Kit thumb
NOTE: For SFF models.
NOTE: HPE 1U Small Form Factor Ball Bearing Gen8 Rail Kit ships standard with some BTO Preconfigured Channel Models.
$360
$250.00
HPE 1U Cable Management Arm for Ball Bearing Rail Kit thumb
NOTE: The HPE 1U Gen8 Cable Management Arm is optional for the SFF and LFF Ball Bearing Rail Kits and is not available for use with the Friction Rail Kit.
$200
$159.00

USB and SD Options

HPE Flash Media Kits for USB Drives

NOTE: HPE qualified blank USB key for use with HPE ProLiant servers that support the VMware virtualization environment and other HPE value-add software. HPE recommends this industry standard USB flash device for use with VMware ESXi. USB device must be installed in the internal slot of the ProLiant server for use with VMware ESXi. Refer to HPE VMware Getting Started Guide for installation instructions.

HPE Enterprise Mainstream Flash Media Kits for Memory Cards

Processors

NOTE: HPE server processor pricing is volatile and availability is unpredictable. Please select any CPU kit below and click Request Quote and submit the form to get the current pricing for that CPU kit.
NOTE: All CPU Kits come complete with heatsink, fan(s), etc
NOTE: Customers who have DL360p Gen8 servers with E5-2600 processors and want to upgrade to E5-2600v2 processors will need to contact their HPE representative for a list of SKUs that are compatible with that system.
NOTE: If two processors are desired, select the second from the xxxxxx-B21 below.

Entry Processors - E5-2600 v2 series Processor kits

Base Processors - E5-2600 v2 series Processor kits

Performance Processors - E5-2600 v2 series Processor kits

Compare Selected