HPE ProLiant ML30 Gen11 Parts

4U tower serverIntel Xeon 6300, Xeon E-2400 or Pentium G7400

The HPE ProLiant ML30 Gen11 is a 4U tower server for one Intel Xeon 6300, Xeon E-2400 or Pentium G7400 processor, and every one of them takes the same memory: DDR5-4800 unbuffered ECC DIMMs (UDIMMs), 16GB or 32GB; registered DIMMs are not supported. This page lists the 81 parts HPE's QuickSpecs have listed for it across editions, by part type.

  • 81 HPE-listed parts
  • 4 DIMM slots, up to 128GB
  • 8 SFF or 4 LFF drives, plus one M.2
  • 1 PCIe 5.0 and 3 PCIe 4.0 slots
  • 350W ATX or Flex Slot 500W to 1000W

Specifications: HPE QuickSpecs a50007008enw, version 27 (August 3, 2026). Memory and drive figures match the ML30 Gen11 Memory and Drives pages.

Shop ML30 Gen11 parts by type

More ML30 Gen11 parts: chassis, expansion and enablement

Most ordered from this list

The parts on this page our customers order most, for any server.

  1. DrivesP28352-B212.4TB SAS 12G Mission Critical 10K SFF BC 3-year 512e Multi Vendor HDD
  2. Boot devicesP48183-B21NS204i-u Gen11 NVMe Hot Plug Boot Optimized Storage Device
  3. DrivesP40500-B213.84TB SATA 6G Read Intensive SFF BC Multi Vendor SSD
  4. Drives861686-B211TB SATA 6G Business Critical 7.2K LFF LP 1-year Multi Vendor HDD
  5. DrivesP28586-B211.2TB SAS 12G Mission Critical 10K SFF BC 3-year Multi Vendor HDD
  6. DrivesP40498-B21960GB SATA 6G Read Intensive SFF BC Multi Vendor SSD
  7. DrivesP47808-B21960GB SATA 6G Read Intensive LFF LPC Multi Vendor SSD
  8. Drives881787-B2112TB SATA 6G Business Critical 7.2K LFF LP 1-year Helium 512e Multi Vendor HDD
  9. Drives861683-B214TB SATA 6G Business Critical 7.2K LFF LP 1-year Multi Vendor HDD
  10. DrivesP40505-B213.84TB SATA 6G Mixed Use SFF BC Multi Vendor SSD

ML30 Gen11 at a glance

Processors

One processor: Intel Xeon 6300 (6315P to 6377P), Xeon E-2400 (E-2414 to E-2488) or Pentium G7400.

Processors of 95W, such as the Xeon 6369P and E-2488, need the High Performance Heat Sink Kit (P65108-B21), and HPE's note under the 65W Xeon 6353P asks for it too. HPE marks the kit FIO, factory-installed only. ML30 Gen11 Processors

Memory

4 DIMM slots on 2 channels. DDR5-4800 ECC UDIMMs only, 16GB or 32GB; no RDIMMs, LRDIMMs or non-ECC UDIMMs.

Up to 128GB with 32GB in all four slots. The kits run at up to 4400 MT/s; with Xeon E and Pentium processors HPE lists 4000 MT/s (16GB) or 3600 MT/s (32GB) with two DIMMs in a channel. Both DIMMs in a channel must be the same capacity, and HPE does not recommend mixing capacities at all; it recommends 1, 2 or 4 DIMMs. ML30 Gen11 Memory

Drives

4 LFF non-hot-plug SATA, 4 LFF hot-plug or 8 SFF hot-plug drives, depending on the model, plus one M.2 NVMe slot.

SAS drives need a tri-mode controller, which the 4LFF non-hot-plug model does not support. The NS204i-u boot device needs its cable kit (P65098-B21) and cannot be fitted with an optical drive. ML30 Gen11 Drives

Storage controllers

Embedded Intel VROC SATA RAID: disabled by default, UEFI boot mode only, no VMware. MR216i-p, MR408i-p and MR416i-p tri-mode controllers; HPE allows one MR416i-p or MR216i-p at most, for better performance.

A tri-mode controller needs a Smart Storage Battery (P01367-B21) or Hybrid Capacitor (P02381-B21), the battery holder (786710-B21) and a cable kit for the cage: P57104-B21 for 4LFF hot-plug, P67850-B21 for 8SFF. HPE lists both cable kits; the store's list does not.

The Smart Array E208e-p is for external storage only and does not fit the non-hot-plug model. ML30 Gen11 Storage Controllers

Networking

Four embedded 1GbE ports, port 1 shared with iLO, and PCIe adapters. A dedicated iLO port comes with the iLO/NIC/M.2/COM Port Kit (P65741-B21), which fits the board's M.2 slot and carries an M.2 slot of its own. HPE lists this kit; the store's list does not. ML30 Gen11 Networking

Expansion

Four slots: one PCIe 5.0 x16 (slot 1) and three PCIe 4.0 x4 with x8 connectors. A SAS controller and a PCIe 5.0 x16 card both need slot 1, so they do not go together.

The Front PCI Fan and Baffle Kit (P65106-B21) is required in the hot-plug models, and in the non-hot-plug model with an M.2 SSD or any PCIe card other than the E208e-p or a 1Gb adapter. HPE lists this kit; the store's list does not.

Power

One 350W non-redundant ATX power supply, factory-installed only, or one or two Flex Slot hot-plug supplies (500W, 800W or 1000W), which need the RPS Enablement Kit (P65104-B21). A second supply must have the same part number as the first. ML30 Gen11 Power Supplies

Management

HPE iLO 6.

Specifications from HPE QuickSpecs a50007008enw, version 27 (August 3, 2026). Memory figures match the ML30 Gen11 Memory page.

Before you order memory, check that it is unbuffered (UDIMM). The ML30 Gen11 takes only HPE DDR5-4800 unbuffered ECC DIMMs: the 16GB P64336-B21 and the 32GB P64339-B21. Registered DIMMs (RDIMMs) and LRDIMMs are not supported, and HPE does not qualify memory from earlier server generations in it. Before you reuse or order a kit, type its part number into the check on this page to see whether it is on the ML30 Gen11 list.

Complete your ML30 Gen11 build

Is it an ML30 Gen11? How to tell

The processor model number and the memory type identify an ML30 Gen11.

What to checkML30 Gen11 This page
Processor model numbers63xxP, E-24xx or G7400: Xeon 6315P, E-2434, Pentium G7400
MemoryDDR5-4800 UDIMM, 4 slots
Memory kits look likeP64336-B21, P64339-B21
Parts pageYou are here

From the HPE QuickSpecs of each server: HPE ProLiant ML30 Gen11 a50007008enw version 27.

All 81 ML30 Gen11 parts

Grouped by part type; within each group the parts are in the order of HPE's QuickSpecs. Open a group, or type a part number or a few words to filter the whole list.

ML30 Gen11 parts questions

How much memory does the ML30 Gen11 support?

Up to 128GB: 32GB DDR5-4800 unbuffered ECC DIMMs (UDIMMs) in all four slots. Registered and load-reduced DIMMs are not supported. The kits run at up to 4400 MT/s, and the two DIMMs in a channel must be the same capacity.

Which drives fit the ML30 Gen11?

2.5-inch SFF drives on the Basic Carrier (BC) in the 8SFF hot-plug model, 3.5-inch LFF drives on the Low Profile (LP) carrier in the 4LFF hot-plug model, both in SAS or SATA, and LFF SATA drives in the 4LFF non-hot-plug model. SAS drives need a tri-mode controller. Every model also has one M.2 NVMe slot.

How do I tell which processor my ML30 Gen11 has?

Read the processor model in iLO under System Information › Processors. Xeon 6300 models are numbered 63xxP (such as 6315P), Xeon E-2400 models E-24xx (such as E-2434), and the Pentium is the G7400. All of them take the same DDR5-4800 UDIMM kits. Processors of 95W need the High Performance Heat Sink Kit (P65108-B21), and HPE's note under the 65W Xeon 6353P asks for it too. HPE marks the kit FIO, factory-installed only.

Is my server an ML30 Gen11?

Check the processor model number. An ML30 Gen11 runs an Intel Xeon 6300 (63xxP), Xeon E-2400 (E-24xx) or Pentium G7400 processor, with DDR5-4800 UDIMM memory in 4 slots. HPE does not qualify memory from earlier server generations in the ML30 Gen11, so buy memory from the page for your generation.

Are refurbished parts on this list too?

Yes. A refurbished part carries the same HPE part number as a new one, so it is listed here under that number, and each listing shows its condition. Every part ships tested or factory sealed.

What warranty comes with ML30 Gen11 parts?

A replacement warranty of 1 to 5 years, depending on the part: memory is covered for 5 years, and many other parts for 1 or 3 years.

Other ML30 generations

ML30 Gen10 partsAll HPE parts by server model
Ships same dayMost orders ship the same business day
1 to 5 year warrantyTested or factory sealed
Purchase orders acceptedCard, P-card, ACH, wire or PayPal too
Drives41 parts

All drives on the ML30 Gen11 Drives page

Hard Disk Drives

Enterprise - 12G SAS -- SFF Basic Carrier Drives
Midline - 12G SAS - LFF Low Profile Carrier Drives
Midline - 6G SATA - LFF Low Profile Carrier Drives
6G SATA - LFF NHP/Raw Drives
HPE note

ML30 Gen10 Plus supports up to SAS 12G. Performance downgraded to 12G is expected once SAS

HPE Solid State Drives

Read Intensive -- 24G SAS - SFF Basic Carrier Solid State Drives
Mixed Use -- 12G Value SAS - SFF Basic Carrier Solid State Drives
Read Intensive -- 12G Value SAS - SFF Basic Carrier Solid State Drives
Mixed Use -- 6G SATA - SFF Basic Carrier Solid State Drives
Read Intensive -- 6G SATA - SFF Basic Carrier Solid State Drives
Read Intensive -- 6G SATA - LFF Low Profile Carrier Solid State Drives
Read Intensive - NVMe - M.2 - Solid State Drives
Memory2 parts

All memory on the ML30 Gen11 Memory page

Unbuffered DIMMs (ECC UDIMMs)

HPE note

The maximum memory speed is a function of the memory type, memory configuration, and processor model.

Network adapters8 parts

All network adapters on the ML30 Gen11 Networking page

1 Gigabit Ethernet adapters
10 Gigabit Ethernet adapters
25 Gigabit Ethernet adapters
HPE notes (3)
  • Any PCIe card selection requires selection of the HPE ML30 Gen11 Front PCI Fan and Baffle Kit (P65106-B21)
  • SAS controllers (internal and external) and PCIe Gen5 x16 card cannot be selected together as both need to be installed on slot 1
  • If controller x8 and PCIe x8 card is selected together, then the controller should be installed on Slot 1 and PCIe x8 card on slot 2
Storage controllers4 parts

All storage controllers on the ML30 Gen11 Storage Controllers page

Essential RAID Controllers
HPE Tri-Mode Controllers
HPE notes (5)
  • Tri-Mode controllers are not supported on the 4LFF Non-Hot Plug Model Server.
  • Max 1 pc of MR416i-p or MR216i-p can be selected for better performance.
  • Must select 1pc HPE ML30 Gen10+ BCM Cable Kit (P57104-B21) for 4LFF Hot Plug Server.
  • Must select 1pc HPE ML30 Gen11 SFF PCIe Cable Kit (P67850-B21) for 8SFF Hot Plug Server.
  • Tri-Mode controller selection requires selection of either P01367-B21 - HPE 96W Smart Storage Lithiumion Battery with 260mm Cable Kit or P02381-B21 - HPE Smart Storage Hybrid Capacitor with 260mm Cable Kit
Power supplies4 parts

All power supplies on the ML30 Gen11 Power Supplies page

Processors17 parts

All processors on the ML30 Gen11 Processors page

  • P77162-B21 Intel Xeon 6369P 3.3GHz 8-core 95W Processor for HPE
  • P77163-B21 Intel Xeon 6357P 3.0GHz 8-core 80W Processor for HPE
  • P77164-B21 Intel Xeon 6353P 2.7GHz 8-core 65W Processor for HPE
  • P77165-B21 Intel Xeon 6349P 3.6GHz 6-core 95W Processor for HPE
  • P77166-B21 Intel Xeon 6337P 3.5GHz 6-core 80W Processor for HPE
  • P77167-B21 Intel Xeon 6333P 3.1GHz 6-core 65W Processor for HPE
  • P77168-B21 Intel Xeon 6325P 3.5GHz 4-core 55W Processor for HPE
  • P77169-B21 Intel Xeon 6315P 2.8GHz 4-core 55W Processor for HPE
  • P65218-B21 Intel Xeon E-2488 3.2GHz 8-core 95W Processor for HPE
  • P65219-B21 Intel Xeon E-2478 2.8GHz 8-core 80W Processor for HPE
  • P65221-B21 Intel Xeon E-2486 3.5GHz 6-core 95W Processor for HPE
  • P65220-B21 Intel Xeon E-2468 2.6GHz 8-core 65W Processor for HPE
  • P65222-B21 Intel Xeon E-2456 3.3GHz 6-core 80W Processor for HPE
  • P65223-B21 Intel Xeon E-2436 2.9GHz 6-core 65W Processor for HPE
  • P65224-B21 Intel Xeon E-2434 3.4GHz 4-core 55W Processor for HPE
  • P65225-B21 Intel Xeon E-2414 2.6GHz 4-core 55W Processor for HPE
  • P65226-B21 Intel Pentium G7400 3.7GHz 2-core 46W Processor for HPE
Boot devices2 parts

HPE Boot Controllers

HPE notes (3)
  • The N204i-u Boot device includes 2x 480GB M.2 NVMe SSDs, with preconfigured hardware RAID1. For additional information, please see the HPE OS Boot Device QuickSpecs.
  • Selection of the HPE NS204i-u Gen11 NVMe Hot Plug Boot Optimized Storage Device requires selection of the HPE ProLiant ML30 Gen11 NS204i-u Hot Plug Boot Optimized Storage Device Cable Kit. Both the device and the enablement kit are required to be selected together.
  • The HPE N204i-u Boot device and Optical Disk Drives cannot be selected together
Energy packs3 parts
Ships same dayMost orders ship the same business day
1 to 5 year warrantyReplacement coverage on every part
5,000+ five-star reviewsShopper Approved, BBB A+ rating
Ships to 120+ countriesBy UPS; duties are collected by the carrier

Building out several servers, or need a part not listed?

Send the part numbers and quantities for each server and we reply to every quote request within 24 hours. Live chat is the fastest way to reach us.

!