HPE ProLiant SL390s G7 Parts
Unique Options
NOTE: Needed to enable Infiniband using QSFP port on system board.
$161
$128.00
NOTE: needed if use SAS drives instead of SATA drives.
NOTE: This is needed when using internal non hot plug drive in 2U tray.
NOTE: required for every 2 SFF drives being added to the 1U tray.
NOTE: this is required when add two 3.5" SAS drive to the 1U tray.
NOTE: this is required when add four 3.5" SAS drive to the 1U tray.
NOTE: riser need when adding 2 GPUs to 2U tray.
$588
$529.00
NOTE: needed when adding 1 GPU to 2U tray.
NOTE: also needed if adding 3rdd GPU to 2U tray.
$306
$275.00
NOTE: It is required that the entire chassis be filled with fans - Part number only contains 1 fan, 8 must be purchased.
$92
$65.00
NOTE: It is required that the entire chassis be filled with fans - Part number only contains 1 fan, 8 must be purchased.
$82
$62.00
$3,381
$2,450.00
NOTE: service tray needed when removing ½ width tray for service.
$1,721
$1,549.00
NOTE: Node blank is needed when not completely filling s6500 chassis.
NOTE: 1 node blank is needed for every 1U half width space left in chassis.
$156
$124.00
$142
$113.00
Memory
Registered DIMMs (RDIMMs)
$49
$38.00
$54
$38.00
$50
$39.00
$81
$65.00
NOTE: Low Voltage DIMMs can only be used with Intel Xeon processor 5600 series processors.
$67
$48.00
$56
$39.00
$56
$39.00
NOTE: Low Voltage DIMMs can only be used with Intel Xeon processor 5600 series processors.
Unbuffered with ECC DIMMs (UDIMMs)
$57
$38.00
$66
$45.00
$67
$48.00
$237
$175.00
NOTE: There is a maximum support limitation of 8 ranks per memory channel (maximum of 2 quad rank DIMMs per channel)
NOTE: PC3L is a low voltage memory.
NOTE: Memory Min and Max depends on number of processors and type of memory:
null
1. Processor -> R-Dimm: Min 1 // Max 6 U-Dimm: Min 1 // Max 12
2. Processors -> R-Dimm: Min 2 // Max 6 U-Dimm: Min 2 // Max 12
null
Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.
NOTE: The non-hot plug hard drives use a quick release carrier.
NOTE: Hot plug hard drives are for 2U tray only.
NOTE: non hot plug with quick release carrier are used in 1U tray and internal to the 2U tray.
SAS Hot Plug 2.5" SFF Enterprise (ENT) Drives
12G 15K Drives
12G = 12 Gb/sec Transfer Rate Synchronous (Maximum)
15K = 15,000 rpm Rotational Speed
12G 10K Drives 
12G = 12 Gb/sec Transfer Rate Synchronous (Maximum)
10K = 10,000 rpm Rotational Speed
6G 15K Drives
6G = 6 Gb/sec Transfer Rate Synchronous (Maximum)
15K = 15,000 rpm Rotational Speed
6G 10K Drives
6G = 6 Gb/sec Transfer Rate Synchronous (Maximum)
10K = 10,000 rpm Rotational Speed
3G 15K Drives
3G = 3 Gb/sec Transfer Rate Synchronous (Maximum)
15K = 15,000 rpm Rotational Speed
3G 10K Drives
3G = 3 Gb/sec Transfer Rate Synchronous (Maximum)
10K = 10,000 rpm Rotational Speed
NOTE: Please see the SAS Hard Drive QuickSpecs for Technical Specifications such as capacity, height, width, interface, transfer rate, seek time, physical configuration, and operating temperature:
SAS Hot Plug 2.5" SFF Midline (MDL) Drives
$133
$95.00
$186
$128.00
SATA Hot Plug 2.5" SFF Midline (MDL) Drives
$144
$98.00
$83
$58.00
$288
$220.00
SATA Hot Plug 2.5" SFF Entry (ETY) Drives
$270
$199.00
$97
$75.00
SATA Hot Plug 2.5" Midline (MDL) Solid State Drives
RECOMMENDATION: For best performance of SSD drives it is recommended that any Smart Array Controller use a max of 4 drives. For this product a second Smart Array option can be used for the second set of 4 SSD drives.
SAS Non-Hot Plug Enterprise (ENT) Drives - with quick-release (QR) carrier
$215
$149.00
$92
$73.00
SATA Non-Hot Plug Entry (ETY) Drives - with quick-release (QR) carrier
SATA Non-Hot Plug Midline (MDL) Drives - with quick-release (QR) carrier
NOTE: HPE P212 SAS 4HDD Cable Kit (574001-B21) is needed when adding more than two 2.5" hard drives.
SATA Non-Hot Plug Midline (MDL) Solid State Drives - with quick-release (QR) carrier
NOTE: The non-hot plug hard drives use a quick release carrier.
NOTE: One 2 Drive SFF Drive Cage (582657-B21) is required when installing 2 SFFF drives.
NOTE: When Adding SAS one of the following cable kits needs to be ordered depending on which SAS controller installing - HPE P212 SAS 4HDD Cable Kit 574001-B21 or HPE P410 SAS 4HDD Cable Kit 583997-B21.
NOTE: Hot plug hard drives are for 2U tray only.
NOTE: non hot plug with quick release carrier are used in 1U tray and internal to the 2U tray.
Networking
Gigabit Ethernet Adapters
$81
$59.00
$165
$125.00
$161
$115.00
$72
$55.00
$111
$79.00
10 Gigabit Ethernet adapters
NOTE: The SL390s G7 supports only the low-profile version of the 10GbE Ethernet Adapters.
NOTE: No more than two 10GbE I/O devices are supported in a single ProLiant server.
NOTE: A minimum of two Gigabytes (2 GB) of server memory is required per each adapter.
NOTE: Direct Attach Cable (DAC) for copper environments or fiber transceivers and cables for fiber-optic environments must be purchased separately.
InfiniBand
$609
$450.00
I/O Expansion Options
$588
$529.00
$306
$275.00
Power Supplies
CAUTION: In ProLiant Servers that have more than one power slot (bay), only same size power supplies are recommended. If non-matched power supplies are inserted you will get errors and operation will fail.
$184
$138.00
Rail Options
$156
$124.00
$142
$113.00
Storage Controllers
SAS Controllers
Smart Array P212 Controller
Smart Array P410 Controller
$94
$71.00
Smart Array P411 Controller
$270
$203.00
$500
$335.00
$522
$399.00
Optional Upgrades
$41
$29.00
$53
$39.00
$67
$48.00
NOTE: To enable BBWC on the 256MB cache.
$207
$156.00
SCSI HBA
NOTE: Recommended HBA for SCSI tape drive connect.
$207
$149.00
Processors
| NOTE: HPE server processor pricing is volatile and availability is unpredictable. Please select any CPU kit below and click Request Quote and submit the form to get the current pricing for that CPU kit. |
NOTE: All CPU Kits come complete with heatsink, fan(s), etc
Six-Core Processors
Quad-Core Processors
Dual-Core Processors
NOTE: 130 watt processors are only available on 1U half width tray in s6500 chassis with non-redundant fans.
NOTE: HT indicates that the processor model supports Intel Hyper-Threading Technology.
NOTE: Turbo indicates the maximum potential frequency increment when using Intel Turbo Boost Technology, with 4, 3, 2, and 1 cores active.
NOTE: DDR3 speed is the maximum memory speed of the processor. Actual memory speed may depend on the quantity and type of DIMMs installed.
NOTE: For the Intel 5500 Series, the letter preceding the model number indicates the performance/wattage of the processor. X denotes High Performance/Wattage; E denotes Enterprise Performance/Wattage (Mainstream); and L denotes Lower Wattage.
Why Global One?
- Trusted by thousands. Over 32,000 customers in 100+ countries trust Global One Technology to deliver mission-critical HP Enterprise hardware - including Fortune 500 businesses, schools, hospitals, and federal, state, and local goverment agencies.
- HPE is our specialty! We only sell genuine HP Enterprise parts.
- EASY ordering process. Purchase online now with credit card or PayPal!
- FAST shipping. Global One Technology ships orders received by 5pm the same day and offers NEXT DAY delivery to US customers.
