HPE ProLiant BL420c Gen8 Parts

HPE ProLiant BL420c Gen8 Parts

HPE ProLiant BL420c Gen8 Parts

Networking

NOTE:  Each 10 Gigabit Ethernet adapter requires a minimum of 2GB of server memory.
NOTE:  A 10 Gigabit Ethernet adapter supports linking at 1Gbps or 10Gbps when connected to an interconnect module with 10Gb Ethernet downlinks. 
NOTE:  A 10 Gigabit Ethernet adapter supports linking at only 1Gbps when connected to an interconnect module with 1Gb Ethernet downlinks. 
NOTE:  The 10 Gigabit Ethernet adapters on each server blade connect to a 10Gb interconnect in bays 3-8 (HPE BladeSystem c7000 Enclosure) or bays 2-4 (HPE BladeSystem c3000 Enclosure).

10 Gigabit Ethernet Mezzanines

1 Gigabit Ethernet Mezzanines

FlexibleLOM Adapters

NOTE:  The server supports one (1) FlexibleLOM that is installed in the FlexibleLOM connectors and is already included in the pre-configured models. However, it must be added in Step 2 for Configure-to-order Models. The FlexibleLOM options below are used to change these original FlexibleLOMs.

10 Gigabit Ethernet FlexibleLOM Adapters

1Gb FlexibleLOM Adapters

Memory

NOTE:  To realize the performance memory capabilities for this server, HPE SmartMemory is required. For additional information, please see the HPE SmartMemory QuickSpecs at:
NOTE:  HPE memory from previous generation servers are not fully compatible with Smart Memory features in Gen8 Servers.
NOTE:  A minimum of one DIMM is required per server.
NOTE:  For additional memory rules and guidelines, see the "Memory" section of the Quickspecs document for this server.

HPE SmartMemory

Registered DIMMs (RDIMMs)

Unbuffered with ECC DIMMs (UDIMMs)

Load Reduced DIMMs (LRDIMMs)

HPE 32GB (1x32GB) Quad Rank x4 PC3L-10600L (DDR3-1333) Load Reduced CAS-9 Low Voltage Memory Kit thumb
NOTE:  Depending on the memory configuration and processor model, 1600MHz and 1333MHz memory may operate at a lower speed. Please see the the Online Memory Configuration Tool for details at: 
$147
$105.00

Drives

NOTE:  The ProLiant BL420c Gen8 server includes the new HPE hot-plug small form factor (SFF) SmartDrive carrier for enhanced management and reduced maintenance errors. HPE drives from previous generation servers are not compatible with the BL420c Gen8 drive bays.
NOTE:  The mixing of standard SAS drives with SAS SSD is supported within the server, but limits the RAID configuration to two separate RAID 0 volumes. Mixing of other drives types is not supported.
NOTE:  The hard drive options are not required when configuring a drive-less model.

6G SATA Hot Plug with SmartDrive SFF (2.5-inch) Midline (MDL) Drives

SAS Hot Plug with Smart Drive SFF (2.5-inch) Enterprise Drives

12G 15K Drives

12G 10K Drives

6G 15K Drives

6G 10K Drives

SAS Hot Plug SmartDrive SFF (2.5-inch) Enterprise 512e Drives

SAS Hot Plug SmartDrive SFF (2.5-inch) Midline Drives

6G SAS ME Hot Plug SFF (2.5-inch) Enterprise Mainstream Solid State Drives

6G SAS SLC Hot Plug SFF (2.5-inch) Enterprise Performance Solid State Drives

3G SATA MLC Hot Plug SFF (2.5-inch) Enterprise Mainstream Solid State Drives

HPE 100GB 3G SATA MLC SFF (2.5-inch) SC Enterprise Mainstream Solid State Drive thumb
NOTE:  The mixing of standard SAS drives with SAS SSD is supported within the server, but limits the RAID configuration to two separate RAID 0 volumes. Mixing of other drives types is not supported.
NOTE:  HPE Dynamic Smart Array B320i Controller requires a SAS license key for RAID 0 and 1 functionality for SAS drives when selecting a Configure-to-Order server. The SAS RAID license comes standard with preconfigured servers. SATA RAID 0/1 standard.
$399
$281.00

Storage Controllers

Smart Array Guide

HPE Smart Array P721m Controller

Optional Upgrades

HPE Dynamic Smart Array B320i Specific Options:

NOTE:  The following storage controller options below are not supported on the HPE Smart Array P220i controller.

InfiniBand Mezzanines

NOTE:  When an InfiniBand adapter is installed in mezzanine slot 1, only one port is active (regardless of operating mode). When installed in any other mezzanine slot, both ports are active.
HPE QDR/EN InfiniBand 10Gb Dual Port 544M Adapter thumb
NOTE:  The QDR InfiniBand adapter may be installed in any mezzanine slot of the server.
$91
$65.00
HPE FDR/EN InfiniBand 10/40Gb Dual Port 544M Adapter thumb
NOTE: The FDR InfiniBand adapter must be installed in mezzanine slot 1 for FDR mode and may be installed in any mezzanine slot if operated in any other mode.
$210
$158.00

Ultrium Tape Blades

HPE LTO-4 SB1760c Tape Blade thumb
NOTE:  LTO-4 Ultrium tape technology.
HPE LTO-5 SB3000c Tape Blade thumb
NOTE:  LTO-5 Ultrium tape technology.
$7,222
$6,500.00

Storage Blades

Expansion Blade

HPE BLc PCI Expansion Blade thumb
NOTE:  The PCI Expansion Blade provides PCI card slots for an adjacent c-Class Server Blade. Order one PCI expansion Blade for each server blade needing standard PCI-X or PCIe expansion slots. 
NOTE:  Ships with one pre-installed PCI-X connect board. Also includes one PCIe connect board which requires installation.
$359
$246.00

Processors

NOTE: HPE server processor pricing is volatile and availability is unpredictable. Please select any CPU kit below and click Request Quote and submit the form to get the current pricing for that CPU kit.
NOTE: All CPU Kits come complete with heatsink, fan(s), etc
NOTE: The BL420c Gen8 supports one or two processors.
NOTE: The BL420c Gen8 includes two I/O mezzanine expansion slots. A processor must be installed in processor slot 1 for access to the first mezzanine expansion slot (expansion slot 1). A processor must be installed in processor slot 2 for access to the second mezzanine expansion slot (expansion slot 2).
NOTE: All processors within the server must be identical.
NOTE: The letter L preceding the model number indicates denotes lower wattage.
NOTE: The processor model as well as the memory configuration determines the maximum speed memory can operate. Please see the see the Memory section later in this document.

Eight-Core Processors

Six-Core Processors

Quad-Core Processors

Compare Selected