HPE ProLiant DL380 Gen10 Parts

2U rack server1st and 2nd Gen Intel Xeon Scalable

The HPE ProLiant DL380 Gen10 is a 2U rack server for one or two 1st or 2nd Gen Intel Xeon Scalable processors, and the processor's generation decides its memory: DDR4-2666 kits for 1st Gen, DDR4-2933 for 2nd Gen. This page lists the 537 parts HPE's QuickSpecs have listed for it across editions, by part type.

  • 537 HPE-listed parts
  • 24 DIMM slots, up to 3TB
  • Up to 30 SFF or 19 LFF + 2 SFF drives
  • Up to 8 PCIe 3.0 slots on 3 risers
  • Flex Slot power, 500W to 1800W-2200W

Specifications: HPE QuickSpecs a00008180enw, version 77 (June 16, 2025), which HPE has retired. Memory and drive figures match the DL380 Gen10 Memory and Drives pages.

Shop DL380 Gen10 parts by type

More DL380 Gen10 parts: chassis, expansion and enablement

Most ordered from this list

The parts on this page our customers order most, for any server.

  1. Drives872479-B211.2TB SAS 12G Mission Critical 10K SFF SC Multi Vendor HDD
  2. MemoryP00924-B2132GB (1x32GB) Dual Rank x4 DDR4-2933 CAS-21-21-21 Registered Smart Memory Kit
  3. Memory815100-B2132GB (1x32GB) Dual Rank x4 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit
  4. Drives872477-B21600GB SAS 12G Mission Critical 10K SFF SC Multi Vendor HDD
  5. Drives881457-B212.4TB SAS 12G Mission Critical 10K SFF SC 512e Multi Vendor HDD
  6. Network adapters811546-B21Ethernet 1Gb 4-port BASE-T I350-T4V2 Adapter
  7. DrivesP28352-B212.4TB SAS 12G Mission Critical 10K SFF BC 512e Multi Vendor HDD
  8. Drives872481-B211.8TB SAS 12G Mission Critical 10K SFF SC 512e Multi Vendor HDD
  9. Drives765466-B212TB SAS 12G Midline 7.2K SFF (2.5in) SC 512e HDD
  10. Power supplies865414-B21800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit

DL380 Gen10 at a glance

Processors

One or two Intel Xeon Scalable processors of the same model, 1st Gen (model numbers x1xx) or 2nd Gen (x2xx). HPE does not support a field upgrade from 1st to 2nd Gen. DL380 Gen10 Processors

Memory

24 DIMM slots, 12 per processor on 6 channels. DDR4-2666 kits for 1st Gen, DDR4-2933 for 2nd Gen. Up to 3TB with 128GB LRDIMMs and processors whose model number ends in M or L; other processors address up to 768GB (1st Gen) or 1TB (2nd Gen) each. 1.54TB with 64GB RDIMMs; the two types do not mix. DL380 Gen10 Memory

Drives

Up to 30 SFF drives (24 front, 6 rear), or 19 LFF plus 2 SFF rear in the 12LFF model; up to 20 NVMe SSDs in the SFF chassis; two M.2 SSDs on the primary riser. The 8SFF BC models take Basic Carrier drives. DL380 Gen10 Drives

Storage controllers

Embedded S100i software RAID on every model; Smart Array E208i, P408i and P816i; Broadcom MegaRAID on the 8SFF BC models. Performance RAID controllers need a Smart Storage Battery or Smart Hybrid Capacitor. DL380 Gen10 Storage Controllers

Networking

4 x 1GbE embedded on models that have it, one FlexibleLOM slot, and PCIe adapters; a dedicated 1Gb iLO port. DL380 Gen10 Networking Adapters

Expansion

Up to 8 PCIe 3.0 slots: 3 on the primary riser, 3 on the secondary and 2 on the tertiary riser, which need processor 2. Riser cards

Power

Flex Slot hot-plug power supplies from 500W to 1800W-2200W, including -48VDC and high-voltage AC/DC models. DL380 Gen10 Power Supplies

Management

HPE iLO 5. Management hardware

Specifications from HPE QuickSpecs a00008180enw, version 77 (June 16, 2025). Memory figures match the DL380 Gen10 Memory page.

Before you order memory or processors, check the processor generation. The second digit of the model number tells you: a 1 (Gold 6130, Silver 4110) is 1st Gen and takes DDR4-2666 kits; a 2 (Gold 6230, Silver 4210) is 2nd Gen and takes DDR4-2933 kits. HPE does not support a field upgrade from 1st to 2nd Gen. Find the model in iLO under System Information › Processors.

Complete your DL380 Gen10 build

Gen10, Gen10 Plus or Gen11? How to tell

The processor model number tells the three DL380 generations apart, and it decides the memory you can buy.

What to checkDL380 Gen10 This pageDL380 Gen10 PlusDL380 Gen11
Processor model numbersx1xx or x2xx: Gold 6130, Gold 6230, Silver 4210x3xx: Gold 6338, Silver 4314x4xx or x5xx: Gold 6430, Gold 6530
MemoryDDR4-2666 or DDR4-2933, 24 slotsDDR4-3200, 32 slotsDDR5-4800 or DDR5-5600, 32 slots
Memory kits look likeP00922-B21, P00924-B21P06029-B21, P40007-B21P43322-B21, P64705-B21
Parts pageYou are hereDL380 Gen10 Plus partsDL380 Gen11 parts

From the HPE QuickSpecs of each server: HPE ProLiant DL380 Gen10 a00008180enw version 77; HPE ProLiant DL380 Gen10 Plus a50002553enw version 42; HPE ProLiant DL380 Gen11 a50004307enw version 48.

All 537 DL380 Gen10 parts

Grouped by part type; within each group the parts are in the order of HPE's QuickSpecs. Open a group, or type a part number or a few words to filter the whole list.

DL380 Gen10 parts questions

How much memory does the DL380 Gen10 support?

Up to 3TB with two processors: 24 slots with 128GB DDR4 LRDIMMs in every one, which needs processors whose model number ends in M or L. Other processors address up to 768GB each (1st Gen) or 1TB each (2nd Gen). With registered DIMMs the maximum is 1.54TB (64GB DDR4-2933 RDIMMs in every slot). A single processor can use only its 12 slots. 1st Gen Intel Xeon Scalable processors take DDR4-2666 kits and 2nd Gen processors take DDR4-2933 kits.

Which drives fit the DL380 Gen10?

SFF drives on the Smart Carrier (SC) in SAS, SATA or NVMe; LFF SAS or SATA drives in the 8LFF and 12LFF models; and SATA M.2 SSDs on the primary riser or in an SCM dual M.2 carrier. The 8SFF BC models take Basic Carrier (BC) SAS and SATA drives instead. Which interfaces work depends on the controller.

How do I tell which processor generation my DL380 Gen10 has?

Read the processor model in iLO under System Information › Processors. The second digit of the model number is the generation: a 1 (Gold 6130, Silver 4110) means 1st Gen, a 2 (Gold 6230, Silver 4210) means 2nd Gen. It decides the memory kit: DDR4-2666 for 1st Gen, DDR4-2933 for 2nd Gen.

Is my server a DL380 Gen10 or a DL380 Gen10 Plus?

Check the processor model number. The Gen10 runs 1st or 2nd Gen Xeon Scalable processors (x1xx or x2xx) with DDR4-2666 or DDR4-2933 memory in 24 slots; the Gen10 Plus runs 3rd Gen (x3xx, such as Gold 6338) with DDR4-3200 memory in 32 slots. Memory kits and processors differ between them, so buy those from the page for your generation.

Are refurbished parts on this list too?

Yes. A refurbished part carries the same HPE part number as a new one, so it is listed here under that number, and each listing shows its condition. Every part ships tested or factory sealed.

What warranty comes with DL380 Gen10 parts?

A replacement warranty of 1 to 5 years, depending on the part: memory is covered for 5 years, and many other parts for 1 or 3 years.

Other DL380 generations

DL380p Gen8 partsDL380e Gen8 partsDL380 Gen9 partsDL380 Gen10 Plus partsDL380 Gen11 partsDL380 Gen12 partsDL380a Gen12 partsAll HPE parts by server model
Ships same dayMost orders ship the same business day
1 to 5 year warrantyTested or factory sealed
Purchase orders acceptedCard, P-card, ACH, wire or PayPal too
Drives250 parts

All drives on the DL380 Gen10 Drives page

Hard Disk Drives - 2.5in SFF SAS

Enterprise - 12G SAS - SFF HDD
Midline - 12G SAS - SFF HDD
Enterprise - 12G SAS – Basic Carrier SFF Drives (Only for use with Broadcom MegaRAID)

Hard Disk Drives - 2.5in SFF SATA

Midline - 6G SATA - SFF HDD

Hard Disk Drives - 3.5in LFF SAS

Enterprise - 12G SAS - LFF HDD
Midline - 12G SAS - LFF HDD

Hard Disk Drives - 3.5in LFF SATA

Midline - 6G SATA - LFF HDD

Solid State Drives - 2.5in SFF SAS

Read Intensive - 12G SAS - SFF - SSD
Read Intensive - 12G SAS - SFF - SC Value SAS DS SSD
Write Intensive - 12G SAS - SFF - SSD
Mixed Use - 12G SAS - SFF - SSD
Mixed Use - 12G SAS - SFF - SC Value SAS DS SSD
Read Intensive - 24G SAS - SFF - Basic Carrier Solid State Drives (Only for use with Broadcom MegaRAID)
Read Intensive - 12G SAS - SFF – Basic Carrier SSD (Only for use with Broadcom MegaRAID)
Read Intensive - SAS - SFF - Basic Carrier Self-encrypting Solid State Drives (Only for use with Broadcom MegaRAID)
Mixed Use - 24G SAS - SFF - Basic Carrier Solid State Drives (Only for use with Broadcom MegaRAID)
Mixed Use - 12G SAS - SFF – Basic Carrier Value SAS Digitally Signed Firmware SSD (Only for use with Broadcom MegaRAID)
Mixed Use - SAS - SFF - Basic Carrier Self-encrypting Solid State Drives (Only for use with Broadcom MegaRAID)

Solid State Drives - 2.5in SFF SATA

Read Intensive - 6G SATA - SFF - SSD
Mixed Use - 6G SATA - SFF - SSD
Very Read Optimized - QLC-NAND SATA - SFF - SSD
Read Intensive - 6G SATA – Basic Carrier SFF - Solid State Drives (Only for use with Broadcom MegaRAID)
Mixed Use - 6G SATA – Basic Carrier SFF - Solid State Drives (Only for use with Broadcom MegaRAID)

Solid State Drives - 3.5in LFF SAS

Mixed Use - 12G SAS - LFF -SSD
Mixed Use - 12G SAS - LFF - SC Value SAS DS SSD

Solid State Drives - 3.5in LFF SATA

Read Intensive - 6G SATA - LFF - SSD
Mixed Use - 6G SATA - LFF - SSD

Solid State Drives - SATA M.2

Read Intensive - 6G SATA - M.2 - Solid State Media (2280 type)
Dual Read Intensive - 6G SATA - UFF SCM M.2 - SSD

Solid State Drives - 2.5in SFF NVMe

Read Intensive - NVMe - SFF - SSD
Write Intensive - NVMe - SFF - SSD
Mixed Use - NVMe - SFF - SSD

Solid State Drives - NVMe Add-in Card

HPE NVMe x8 Lanes Mixed Use HHHL

Hard Drive Blank Kits

Memory20 parts

All memory on the DL380 Gen10 Memory page

HPE DDR4 Memory

Registered DIMMs (RDIMMs) for 2nd Generation Intel Xeon Scalable Series
Registered DIMMs (RDIMMs) for 1st Generation Intel Xeon Scalable Series
Load Reduced DIMMs (LRDIMMs) for 2nd Generation Intel Xeon Scalable Series
Load Reduced DIMMs (LRDIMMs) for 1st Generation Intel Xeon Scalable Series

HPE Persistent Memory (Intel Optane)

HPE Persistent Memory (NVDIMM)

HPE DDR-4 Blank Kit

Network adapters52 parts

All network adapters on the DL380 Gen10 Networking Adapters page

HPE Networking

1 Gigabit Ethernet adapters
10 Gigabit Ethernet adapters
25 Gigabit Ethernet adapters
100 Gigabit Ethernet Adapters
FlexibleLOM adapters
HPE note

Only one FlexibleLOM can be added to the server. These options are upgradeable and can be changed from the original configuration after the server is shipped.

HPE InfiniBand

HPE Smart IO

Pensando Distributed Services Card (DSC)
  • P26966-B21 Pensando Distributed Services Platform DSC-25 Enterprise 10/25Gb 2-port SFP28 Card
    HPE note

    DSC card must be installed in slot 1 when configured with Pensando for HPE iLO Adaptive LOM module (P26969-B21) Each card instance requires one RTU license of Silver or Platinum software. In case of more than one adapter, RTU licenses do not need to be of the same part number. One 3yr/4yr/5yr Silver or 3yr/4yr/5yr Platinum software license must be purchased for every DSC-25 card/adapter in a server.

Converged Network Adapters
Storage controllers13 parts

All storage controllers on the DL380 Gen10 Storage Controllers page

HPE notes (4)
  • All performance RAID controllers are supported by the HPE Smart Storage Hybrid Capacitor (P02377-B21) or HPE Smart Storage Battery (P01366-B21), which supports multiple devices and are sold separately.
  • Flexible Smart Array controllers do not consume a PCIe slot.
  • Smart Array controllers are not supported on HPE DL380 Gen10 NC 8SFF BC CTO Server (P56969-B21) and HPE DL380 Gen10 8SFF BC CTO Server (P56970-B21).
  • Smart Array controllers only support Smart Carrier drives.
HPE note

Supported with 8SFF Basic Carriers Model-X only. Only supports SAS/SATA.

Drive cages and backplanes24 parts
  • 826689-B21 HPE DL38X NVMe 8 Solid State Drive Express Bay Enablement Kit
    HPE note

    This option provides support for up to 8 NVMe drives, and can only be populated in Box 1, Box 2 and Box 3 of the SFF chassis, note Box 1 can only be partially populated with four drives if Box 2 and Box 3 are fully populated with NVMe drives. The HPE DL380 Gen10 High Performance fan kit is required for NVMe support (867810-B21). The HPE DL38X Gen10 4-port 8 NVMe SlimSAS Riser (867807-B21) is required to support this. There are limitations on GPU support with the NVMe bay installed. If configuration is 2x CPU + HPE DL38X NVMe 8 Solid State Drive Express Bay Enablement Kit. Then can only select 4 Port Slimline Secondary riser (873732-B21). Box3: SAS/SATA. Box2: NVMe.

  • 826691-B21 HPE DL38X Gen10 SFF Box1/2 Cage/Backplane Kit
    HPE note

    Supports 8 SAS/SATA SFF drives in Box 1 or 2 to a max of 24 SFF SAS/SATA front.

  • P57773-B21 HPE ProLiant DL380 Gen10 2SFF Premium HDD SAS/SATA BC Front/Rear Backplane Kit
    HPE note

    Max = 2 Supported only with the 8SFF Basic Carriers Model-X Requires selection of a tri-mode controller Requires selection of 2SFF Stacked Tri Mode Cable Kit (P55469-B21).

  • P57774-B21 HPE ProLiant DL380 Gen10 8SFF SAS/SATA BC Box 1-2 Backplane Kit
    HPE note

    Max = 2 Supported only with the 8SFF Basic Carriers Model-X Requires selection of a tri-mode controller If Qty 2 of this 8SFF cage is selected then High Performance Fan Kit (867810-B21) must be selected. Requires selection of HPE ProLiant DL38x 8SFF SAS/SATA Tri-Mode Cable Kit (P55467-B21).

  • 826690-B21 HPE DL38X Gen10 Premium 6 SFF SAS/SATA + 2 NVMe or 8 SFF SAS/SATA Bay Kit
    HPE note

    This kit can be supported in Box 1, 2 or 3 and provides support for up to 6 SAS/SATA + 2 NVMe or 8 SFF SAS/SATA drives per Box. If only populating SFF SAS/SATA, the HPE DL38X Gen10 SFF Box1/2 Cage/Backplane Kit (826691-B21) is the more appropriate option. With NVMe drives a specific riser is required. When adding to Box 1 the addition of the High Performance Fan kit (867810-B21) is required.

  • 826688-B21 HPE DL38X Gen10 2SFF HDD SAS/SATA Riser Kit
    HPE note

    2 SFF in the rear is only supported with a 24 SFF model or 12 LFF model. In the rear this leaves 1x16 slot accessible. Rear drives require the addition of the High Performance Fan kit (867810-B21). Supports UFF SCM drives.

  • 826687-B21 HPE DL38X Gen10 2SFF Premium HDD Front NVMe or Front/Rear SAS/SATA Kit
    HPE note

    HPE DL38X Gen10 Universal Media Bay Kit (826708-B21). NVMe drives require the addition of the High Performance Fan kit (867810-B21). NVMe drives require the addition of an NVMe capable riser. Drive cage can be used in the rear of the chassis, but will not support NVMe drives rear. Supports UFF SCM drives.

  • 873781-B21 HPE DL38X Gen10 8LFF Front 2NVMe HDD Bay Kit
    HPE note

    Supports 2 NVMe in the Universal Media bay (included) on the 8 LFF model. For support of the 2 NVMe drives this will require the addition of the HPE DL38X Gen10 x8/x8/x8 1-port 2 NVMe SlimSAS Riser (867806-B21); or the HPE DL38X Gen10 2-port 4 NVMe SlimSAS Riser (867808- B21). NVMe drives require the addition of the High Performance Fan kit (867810-B21).

  • 867805-B21 HPE DL38X Gen10 8LFF Front 2SFF SAS/SATA HDD Kit
    HPE note

    HPE ProLiant DL380 Gen10 8LFF with Universal Media Bay Configure-to-order Server (868706-B21). For 2 SFF SAS/SATA in UMB on 8 LFF model only.

  • 826685-B21 HPE DL38X Gen10 3LFF Rear SAS/SATA Drive Kit
    HPE note

    This is supported in the LFF model only. 3 LFF rear drives will consume the 2nd riser expansion slot.

  • 826686-B21 HPE DL38X Gen10 4LFF Midplane SAS/SATA HDD Kit
    HPE note

    Supported with both the 8 LFF and 12 LFF models. Ships with low-profile heatsink for installation. Supporting processors below 125W. Additional processors supported with system inlet ambient temperature limitations. See “CPUs Supported with 4LFF mid-tray” below With this mid-tray only single-wide (8.5-inch cards with connections or less) cards are supported. This drive does support hot-swap drives. This requires High Performance Fans (867810-B21).

Additional Drive Cage(s)
HPE note

All kits shown above contain the required drive cage/backplane and tri-mode to SAS/SATA cables.

  • P57772-B21 HPE ProLiant DL38x Gen10 2SFF BC HDD SAS/SATA Riser Kit
    HPE note

    This option is housed in a Riser assembly and will be installed in the rear of the chassis. It can be installed into either the Primary Riser location, the Secondary Riser location, or both if Qty=2 is ordered. Requires selection of a second processor Supported only with the 8SFF Basic Carriers Model-X Requires selection of a tri-mode controller Requires selection of 2SFF riser tri-mode cable kit (P55471-B21)

Riser cards11 parts
HPE notes (3)
  • The Primary Riser shipping default in the chassis is a x8 FH, FL, x16 FH, FL and x8 FH, HL with m.2 support.
  • Must select HPE FIO Enable Smart Array SW RAID (784308-B21) to enable Software RAID, if RAID is required on dual m.2 drives.
  • For a Secondary/Tertiary riser, the second processor is required.
  • 826694-B21 HPE DL38X Gen10 x16/x16 Riser Kit
    HPE note

    Slot 1 (Top slot) and 2 (Middle slot) available in Secondary riser location. NMax Qty=1 Double-wide Accelerator/GPU can be populated Supports Full Height and Full length cards. Bus width x16, x16, Connector Width x16, x16.

  • 870548-B21 HPE DL Gen10 x8/x16/x8 Riser Kit
    HPE note

    Slot 1 (Top slot) and 2 (Middle slot) and 3 (Bottom slot) available in Secondary riser location. No M.2 support on this riser. Supports Full Height, Half- length cards, Full Height, Full-length cards and Full Height, Half- length cards. Bus width x8, x16, x8, Connector Width x8, x16, x8.

  • 867807-B21 HPE DL38X Gen10 4-port 8 NVMe Primary SlimSAS Riser
    HPE note

    Riser supporting up to 8 NVMe drives in Primary location. All PCIe lanes dedicated to NVMe; no additional slots available for expansion via stand-up cards in the Primary riser location. Replaces the default Primary riser This can be connected to an 8SFF NVMe drive cage in box 3. To achieve max 20 NVMe support, connect 4 NVMe drives to the tertiary riser.

  • 826704-B21 HPE DL Gen10 x16/x16 GPU Riser Kit
    HPE note

    Slot 2 (Middle slot) and 3 (Bottom slot) available in Secondary riser location. Max Qty=1 Double-wide Accelerator/GPU can be populated Supports Full Height and Full length cards. Bus width x16, x16, Connector Width x16, x16.

  • 867806-B21 HPE DL38X Gen10 x8/x8/x8 1-port 2 NVMe SlimSAS Riser
    HPE note

    Slot 1 (Top slot) or 2 (Middle Slot) or 3 (Bottom slot) available in Secondary riser location with support for 2 NVMe drives Supports Full Height and half-length cards. Bus width x8, x8, x8 Connector Width x8, x8, x8. If this option is selected and the Premium 2SFF HDD Kit (826687-B21) has also been ordered, then the 2SFF NVMe Instruction Spec (878189-B21) MUST be selected; does not apply to 8LFF server model If this option is selected and HPE DL38X Gen10 Premium 6SFF SAS/SATA + 2SFF NVMe Bay Kit (826690- B21) has also been ordered, then the 6+2 NVMe Instruction Spec (878192-B21) MUST be selected.

  • 867808-B21 HPE DL38X Gen10 2-port 4 NVMe SlimSAS Riser
    HPE note

    Supports up to 4 NVMe drives in Tertiary riser location; All PCIe lanes dedicated to NVMe; no additional slots available for expansion via stand-up cards in the Tertiary riser location.

  • 873732-B21 HPE DL38X Gen10 4-port 8 NVMe Secondary Slim SAS Riser
    HPE note

    Riser supporting up to 8 NVMe drives in Secondary riser location; All PCIe lanes dedicated to NVMe; no additional slots available for expansion via stand-up cards in the Secondary riser location.

  • 875780-B21 HPE DL38X Gen10 2 x8 PCIe Tertiary Riser Kit
    HPE note

    Slot 1 (Top slot) and slot (2) available in Tertiary riser location. Bus width x8, x8; Connector Width x8, x8.

  • 826700-B21 HPE DL38X Gen10 x16 Tertiary Riser Kit
    HPE note

    Slot 1 (Top slot) available in Tertiary riser location. Supports Full Height and full-length card. Bus width x16; Connector Width x16.

  • P38515-B21 HPE DL380 Gen10 Pri/Sec Rsr w/o Retainer
    HPE note

    This riser cage removes the retainer clip for proper fitment of certain NVIDIA GPUs in the primary and/or secondary riser. For such applicable NVIDIA GPUs to be populated in the primary riser, first select the appropriate primary riser unless the default x8x16x8 primary is preferred. Then add P38515-B21. For such applicable NVIDIA GPUs in the secondary riser, a secondary riser must first be selected; then add P38515-B21. See “Riser Information” table within this document to select the appropriate primary and/or secondary riser options. If an applicable NVIDIA GPU is installed in both primary and secondary risers, a minimum quantity of (2) of P38515-B21 must be selected if the tertiary riser will not be populated; OR (1) P38515-B21 + (1) P38517-B21 HPE DL380 Gen10 Tertiary Riser without Retainer must be selected if, in addition to both primary and secondary risers containing applicable NVIDIA GPUs, the tertiary riser is being populated with any option, including NVIDIA GPUs.

  • P38517-B21 HPE DL380 Gen10 Tert Riser w/o Retainer
    HPE note

    This tertiary riser cage is a butterfly cage for both the secondary riser and tertiary riser. It removes the retainer clip in the secondary riser for proper fitment of certain NVIDIA GPUs, while allowing for a tertiary riser selection as well. This option should be selected if the tertiary riser is being populated with any option, including NVIDIA GPUs, and the secondary riser contains an applicable NVIDIA GPU. First select the appropriate secondary riser and tertiary riser (see “Riser Information” table for riser options); then add P38517-B21.

Power supplies8 parts

All power supplies on the DL380 Gen10 Power Supplies page

HPE Power Supplies

HPE note

Beginning on January 1st, 2024, units sold into the European Union (EU), European Economic Area (EEA), the United Kingdom, Ireland, Switzerland or Turkey, must include more efficient AC power supplies: 94% for multi- output and 96% for single-output. HPE Flexible Slot power supplies are single-output, and part numbers 865438- B21, P03178-B21, and P44712-B21 are 96% efficient, thus meeting requirements. HPE is on target to fulfil compliant systems ahead of time and will begin enforcing these requirements in advance to satisfy requests with the current power supplies by the set deadline.

Processors107 parts

All processors on the DL380 Gen10 Processors page

HPE Processors

2nd Generation Intel Xeon-Platinum
HPE notes (2)
  • Field upgrades from 1st generation processors (x1xx) to 2nd generation processors (x2xx) not supported.
  • All the below models ship with Performance Heatsink unless otherwise noted.
1st Generation Intel Xeon-Platinum
2nd Generation Intel Xeon-Gold
HPE notes (2)
  • Field upgrades from 1st generation processors (x1xx) to 2nd generation processors (x2xx) not supported.
  • All the below models ship with Performance Heatsink unless otherwise noted.
1st Generation Intel Xeon-Gold
2nd Generation Intel Xeon-Silver
HPE notes (2)
  • Field upgrades from 1st generation processors (x1xx) to 2nd generation processors (x2xx) not supported.
  • All the below models do not ship with Performance Heatsink unless otherwise noted
1st Generation Intel Xeon-Silver
2nd Generation Intel Xeon-Bronze
HPE notes (2)
  • Field upgrades from 1st generation processors (x1xx) to 2nd generation processors (x2xx) not supported.
  • All the below models do not ship with Performance Heatsink.
HPE notes (2)
  • Up to two processors supported.
  • The xxxxxx-L21 is the first processor shipped, the xxxxxx-B21 is the 2nd processor and ships with 2 additional fans for factory of field installation.
1st Generation Intel Xeon-Bronze

Heat Sinks

Cable kits11 parts
HPE Cable Options
  • P55467-B21 HPE ProLiant DL38x 8SFF SAS/SATA Tri-Mode Cable Kit
    HPE note

    Max = 2. Supported with 8SFF Basic Carriers Model-X and 8SFF Basic Carrier BTO servers.

  • P55469-B21 HPE ProLiant DL38x Gen10 Plus 2SFF SAS/SATA Tri-Mode Cable Kit
    HPE note

    Max = 2. Supported with 8SFF Basic Carriers Model-X only.

  • P55471-B21 HPE ProLiant DL38x Gen10 Plus 2SFF Rear Tri-Mode Cable Kit
    HPE note

    Max = 2. Supported with 8SFF Basic Carriers Model-X only.

  • 786092-B21 HPE DL380 SFF Smart Array HBA H200/P400 Series SAS Cable Kit
  • 871827-B21 HPE DL38X Gen10 2 Drive NVMe Slim SAS Cable Kit
  • 826709-B21 HPE DL380 Gen10 Mini SAS 3POS Cable Kit
    HPE note

    If more than 8 SATA devices are being supported on the AHCI Embedded SATA controller, then Qty=1 of the SAS 3POS Cable Kit (826709-B21) is required. The AHCI Embedded SATA Controller is standard with all DL380 Gen10 models and can support up to 12 "SATA Only" devices.

Graphics Cable Kits
Fibre Channel HBAs12 parts
Emulex Fibre Channel HBAs
QLogic Fibre Channel HBAs
Boot devices7 parts
HPE USB and SD Options
HPE note

In vSphere 7.0, VMware made changes that impact the use of an SD Card/USB media as a standalone boot device and will be removing support for them after version 7.x. SD Card/USB media can still be used as a standalone boot option through all 7.x releases via published Customer Advisory Usage of SD Card/USB Devices As Standalone Boot Devices Has Changed Due to System Storage Changes For VMware ESXi 7.0 (Or Later). For any major release beyond VMware ESXi 7.x, VMware will require M.2 or another local persistent device as the standalone boot option.

Smart Storage battery2 parts
HPE note

Provides backup power for multiple HPE Smart Array controllers or other devices. Is required with performance RAID controllers.

Optical drives4 parts

HPE Optical Drives

Media Bay Kits
  • 826708-B21 HPE DL38X Gen10 Universal Media Bay Kit
    HPE note

    The HPE DL380 Gen10 Universal Media bay provides front Display Port and 2xUSB 2.0; plus support for 2x SFF front drives or 2 NVME front drives (826687-B21, riser required) and ODD support (Not included); and can only be located in Box1 in either an 8 SFF or 8+8 SFF model. This is a SFF model option only.

Security5 parts
Rack options6 parts
HPE note

Ball bearing and Easy Install rail kits contain telescoping rails which allow for in-rack serviceability. To assist in the installation of the server into the rack an optional installation tool is available by contacting your local services representative (695539-001).

Management hardware2 parts
Fan kits1 part
  • 867810-B21 HPE DL38X Gen10 High Performance Temperature Fan Kit
    HPE note

    This kit is required for specific Ambient temperature environments This kit is also required to support GPUs configurations. This is required for NVMe configurations. This kit provides maximum cooling for your Server. This kit is required when Box 1, 2 and 3 are populated. High Performance fan kit consists of 6 fans, these will need to replace all the standard fans in the unit, and fill all 6 fan cages. The 12 LFF and 24 SFF models (including field upgrades to 24 SFF) will already include 6 High Performance fan kits.

GPUs2 parts

HPE Computation and Graphics Accelerators

HPE notes (4)
  • Performance fans (867810-B21) are required for all GPU installations (Note these ship as standard with the 24SFF and 12LFF models).
  • Performance Heatsinks (826706-B21) are required for Double Wide GPU installations (Note these ship as standard on Processors over 130W processors and the 8256, 8156, 6128, 5222 and 5122)
  • Mixing of GPUs is not supported.
  • System memory should be 2x GPU memory.
  • R8T26C NVIDIA A16 64GB PCIe Non-CEC Accelerator for HPE
    HPE note

    Max Qty = 2 This GPU requires Pwr Cable Kit (871829-B21) to also be selected. This option requires the High Performance Fan Kit (867810-B21) to be selected This option requires the selection of the High Performance Heatsink (826706-B21) Not supported on 12LFF Model-X Only supported with 2nd generation processors Requires selection of HPE DL380 Gen10 Pri/Sec Rsr w/o Retainer (P38515-B21) and/or HPE DL380 Gen10 Tert Riser w/o Retainer (P38517-B21). Selection is based on quantity of Graphics Option selected This option cannot be selected if more than 8NVMe Drives are selected.

  • R9H23C NVIDIA A2 16GB PCIe Non-CEC Accelerator for HPE
    HPE note

    This option requires the High Performance Fan Kit (867810-B21) to be selected This option requires the selection of the High Performance Heatsink (826706-B21) Not supported on 12LFF or 24SFF Model-X Only supported with 2nd generation processors Requires selection of HPE DL380 Gen10 Pri/Sec Rsr w/o Retainer (P38515-B21) and/or HPE DL380 Gen10 Tert Riser w/o Retainer (P38517-B21). Selection is based on quantity of Graphics Option selected This option cannot be selected if more than 16NVMe drives are selected. If Qty 2 of 8SFF Drive Cage (P57774-B21) is selected, then this Graphics option cannot be selected. Max Qty = 8

Ships same dayMost orders ship the same business day
1 to 5 year warrantyReplacement coverage on every part
5,000+ five-star reviewsShopper Approved, BBB A+ rating
Ships to 120+ countriesBy UPS; duties are collected by the carrier

Building out several servers, or need a part not listed?

Send the part numbers and quantities for each server and we reply to every quote request within 24 hours. Live chat is the fastest way to reach us.

!