HPE ProLiant DL325 Gen10 Parts
The HPE ProLiant DL325 Gen10 is HPE's single-socket 1U AMD server — one AMD EPYC 7xx2 Series processor driving 16 DDR4 slots, three PCIe 3.0 slots, and a choice of 8SFF, 8SFF NVMe, or 4LFF front ends. Every part below is genuine HPE, available new and refurbished, and tested for compatibility before it ships. Live pricing for each part number appears in the tables further down this page.
DL325 Gen10 Platform at a Glance
- Processor: one AMD EPYC 7xx2 Series processor — 8 cores (7232P) up to 64 cores (7702P), 120W to 200W
- Memory: 16 DIMM slots on the single socket — 8 channels, 2 DIMMs per channel, DDR4-2933 to 1.0TB of RDIMM or 2.0TB of LRDIMM
- Storage: 8SFF SAS/SATA, 8SFF NVMe, or 4LFF chassis; either SFF chassis takes one optional 2SFF cage for 10 bays
- Expansion: PCIe 3.0 — x16 full-height and x8 low-profile on the primary riser, plus an optional x16 low-profile secondary riser
- Networking: an embedded 4 × 1GbE adapter where equipped — not fitted on boards built for 7xx2 processors — plus one FlexibleLOM slot and PCIe adapters
- Power: a 500W non-hot-plug supply, or Flex Slot hot-plug 500W, 800W, and 1600W units with the DL325 Gen10 Redundant Power Supply Enablement Kit
- Management: HPE iLO 5 with Intelligent Provisioning
Check the rear panel before you order networking. The DL325 Gen10 shipped with an embedded 4 × 1GbE adapter where equipped, but HPE states that LOM is not fitted on boards built for EPYC 7xx2 processors. On those systems the single FlexibleLOM slot or a PCIe card carries all networking.
Full platform detail is in the official HPE DL325 Gen10 QuickSpecs.
Shop DL325 Gen10 Parts by Category
- DL325 Gen10 Memory — DDR4-2933 RDIMMs from 8GB to 64GB and 64GB/128GB LRDIMMs
- DL325 Gen10 Drives — Smart Carrier SAS, SATA, and NVMe SFF drives plus 4LFF spindles
- DL325 Gen10 Storage Controllers — Smart Array E208, P408, and P816 families with the Smart Storage battery
- DL325 Gen10 Networking Adapters — FlexibleLOM and PCIe cards from 1GbE to 100GbE
Comparing chassis? See DL325 Gen10 Plus parts, the two-socket DL385 Gen10 parts, or browse all HPE parts by server model.
DL325 Gen10 Parts FAQ
What processor does the HPE ProLiant DL325 Gen10 use?
One AMD EPYC 7xx2 Series processor - this is a single-socket 1U server. The qualified range runs from the 8-core 7232P and 7262 up to the 64-core 7702P and 7702, at 120W to 200W.
How much memory does the DL325 Gen10 support?
16 DIMM slots on the one processor, in 8 channels of 2. HPE lists a maximum of 1.0TB using 16 x 64GB DDR4-2933 RDIMMs, or 2.0TB using 16 x 128GB LRDIMMs.
How many drives does the DL325 Gen10 hold?
Eight SFF drives on the 8SFF or 8SFF NVMe chassis, rising to ten with the optional 2SFF cage, or four LFF spindles on the 4LFF chassis. Only one 2SFF kit can be fitted, either SAS/SATA or NVMe.
Does the DL325 Gen10 have onboard network ports?
It depends on the board. The chassis shipped with an embedded 4-port 1GbE adapter where equipped, but the QuickSpecs state that adapter is not fitted on newer boards built for 7xx2 series processors. A single FlexibleLOM slot and the PCIe slots carry networking on those systems.
Does the DL325 Gen10 need an extra kit for redundant power supplies?
Yes. The DL325 Gen10 Redundant Power Supply Enablement Kit (P04983-B21) is mandatory before any Flex Slot hot-plug power supply can be used, and mixing two different power supplies is not supported.
Can I mix new and refurbished parts in the DL325 Gen10?
Yes. Genuine HPE parts perform identically whether new or refurbished, and our refurbished stock is tested before shipping - the usual way to add memory, drives, or a second power supply economically.
✅ Looking for a specific DL325 Gen10 part? Browse our full selection below.


