HPE ProLiant DL320 Gen11 Parts

HPE ProLiant DL320 Gen11 Parts

HPE ProLiant DL320 Gen11 Parts

The HPE ProLiant DL320 Gen11 is the single-socket 1U of the Gen11 line, built for the edge — one 4th or 5th Generation Intel Xeon Scalable processor, 16 DDR5 slots, two PCIe 5.0 risers and an OCP 3.0 slot. Every part below is genuine HPE, available new and refurbished, and tested for compatibility before it ships. Live pricing for each part number appears in the tables further down this page.

DL320 Gen11 Platform at a Glance

  • Processors: one Intel Xeon Scalable CPU, 4th or 5th Generation — HPE describes the platform as up to 60 cores and 270W
  • Memory: 16 DDR5 RDIMM slots, 8 channels at 2 DIMMs per channel — stated maximum RDIMM capacity 2.04 TB
  • Chassis types: 4 LFF, 8+2 SFF SAS/SATA/NVMe, 12 LFF, and GPU Dense with a 4SFF U.3 or 8EDSFF NVMe cage
  • Expansion: two PCIe 5.0 x16 FHHL riser slots plus one OCP 3.0 x16 slot with Wake on LAN and iLO sideband — the secondary riser is an option
  • Accelerators: NVIDIA L4, L40, L40S and A16 PCIe cards; the overview cites up to four single-wide GPUs or two double-wide
  • Power and management: Flex Slot hot-plug supplies from 500W upward, HPE iLO 6 with Intelligent Provisioning, embedded TPM 2.0

Check which chassis you own before you order anything. The DL320 Gen11 ships as 4 LFF, 8+2 SFF, 12 LFF and GPU Dense, and the chassis decides which cages and drives fit. It is also a single-socket server — one processor feeds all 16 DIMM slots, both PCIe 5.0 riser slots and the OCP 3.0 slot.

Full platform detail is in the official HPE DL320 Gen11 QuickSpecs.

Shop DL320 Gen11 Parts by Category

Comparing platforms? See DL320 Gen12 parts, or the two-socket DL360 Gen11 parts and DL380 Gen11 parts. Read our guide to how Gen10 and Gen11 compare, or browse all HPE parts by server model.

DL320 Gen11 Parts FAQ

Is the HPE ProLiant DL320 Gen11 a one-socket or two-socket server?
One. HPE describes it as a 1U 1P server, every processor option kit ships with one processor only, and that single socket feeds all 16 DIMM slots, both PCIe 5.0 riser slots and the OCP 3.0 slot.

How much memory does the DL320 Gen11 support?
Sixteen DDR5 RDIMM slots, 8 channels at 2 DIMMs per channel. The QuickSpecs give a maximum RDIMM capacity of 2.04 TB, stated as 16 x 128 GB at 4800 MT/s, and note separately that all processors support up to 2 TB. The largest module HPE lists is 96GB.

What drives does the DL320 Gen11 accept?
Hot-plug SAS, SATA and NVMe, in whichever form factor your chassis carries: 4 LFF, 8+2 SFF, 12 LFF, or GPU Dense with a 4SFF U.3 cage or an 8EDSFF NVMe cage. Two onboard M.2 connectors handle boot media.

Does the DL320 Gen11 have onboard network ports?
The Network Controller section lists an embedded Broadcom BCM5720 Ethernet 1Gb 2-port BASE-T adapter as standard, and the rear view labels an embedded 1GbE x2 network port. The Interfaces table in the same document lists network ports as none, with a choice of OCP or stand-up card. Anything above 1GbE comes from an adapter.

Can the DL320 Gen11 take GPUs?
Yes. HPE lists NVIDIA L4, L40, L40S and A16 PCIe accelerators, and the overview describes PCIe Gen5 support for up to four single-wide GPUs or two double-wide. The A16, L40 and L40S are listed as supported only with the GPU CTO server.

Can I mix new and refurbished parts in the DL320 Gen11?
Yes. Genuine HPE parts perform identically whether new or refurbished, and our refurbished stock is tested before shipping - a common way to add memory, drives, or a second power supply at lower cost.

Looking for a specific DL320 Gen11 part? Browse our full selection below.

Parts Finder Narrow to your model…
Compare Selected