HPE ProLiant DL560 Gen10 Networking Adapters

The DL560 Gen10 takes network adapters in its one FlexibleLOM slot and in up to eight PCIe 3.0 slots on three risers, of which slots 4 to 8 need the second processor. The CTO server has no network controller of its own: networking comes from a FlexibleLOM adapter in the FlexibleLOM slot or from PCIe NIC cards. HPE's QuickSpecs have listed 37 network adapters (Ethernet, InfiniBand, Omni-Path and converged) and 8 Fibre Channel HBAs for it across editions.

  • 45 adapters
  • 1GbE to 25GbE · 16 and 32Gb Fibre Channel
  • New and refurbished
  • Tested or factory sealed

From the HPE ProLiant DL560 Gen10 Server QuickSpecs (a00008181enw, version 45, 04-December-2023), which HPE has retired.

Slot map

Where each adapter goes in a DL560 Gen10

FlexibleLOM
One FlexibleLOM slot, its ports at the rear with port 1 on the right; one FlexibleLOM is chosen from HPE's list of 1Gb to 10/25Gb Ethernet and converged FlexibleLOMs, and HPE also lists an InfiniBand FDR/Ethernet 40/50Gb 547FLR-QSFP adapter pp. 2, 26, 30, 38–39
Built-in ports
None p. 26
Primary riser
Slots 1–3: PCIe 3.0 x8, x16, x8. On processor 1. + 2 other risers HPE lists for this position pp. 2, 8
Secondary riser
Slots 4–6 (riser kit 870548-B21): PCIe 3.0 x8, x16, x8. Needs processor 2. + 2 other risers HPE lists for this position pp. 2, 9
Tertiary riser
Slots 7–8 (riser kit 872253-B21): PCIe 3.0 x8, x8. Needs processor 2. + 1 other riser HPE lists for this position pp. 2, 9
HPE's words for each line
  • FlexibleLOM “FlexibleLOM slot (various options can be chosen for networking;” (page 26) “FlexibleLOM ports (Port 1 on right side)” (page 2) “Step 2d: Choose network adapters” (page 30) “Only one of the following from each list unless otherwise noted” (page 30) “FlexibleLOM Adapters” (page 38) “HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter 879482-B21” (page 39)
  • Built-in ports “Network Controller None. FlexibleLOM slot (various options can be chosen for networking; NIC cards also available via expansion slots)” (page 26)
  • Primary riser “Primary Riser (Standard)-Default” (page 8) “1 PCIe 3.0 x8 ¾ length/full height Proc 1” (page 8) “2 PCIe 3.0 X16 ¾ length/full height Proc 1” (page 8) “3 PCIe 3.0 x8 ¾ length/full height Proc 1” (page 8) “PCIe Slots (Slots 1-3 top to bottom, riser shipped | standard)” (page 2)
  • Secondary riser “Secondary Riser (Optional) 870548-B21 HPE DL Gen10 x8/x16/x8 Riser Kit” (page 9) “4 PCIe 3.0 x8 Half length/full height Proc 2” (page 9) “5 PCIe 3.0 x16 Half length/full height Proc 2” (page 9) “6 PCIe 3.0 x8 Half length/full height Proc 2” (page 9) “PCIe Slots (Slots 4-6 top to bottom, requires second riser | card and second processor)” (page 2)
  • Tertiary riser “Tertiary bufferfly riser (Optional) 872253-B21 HPE DL560 Gen10 x8/x8 Tertiary Riser Kit” (page 9) “7 PCIe 3.0 x8 Half length/full height Proc 2” (page 9) “8 PCIe 3.0 x8 Half length/full height Proc 2” (page 9) “Tertiary riser (Optional) 872255-B21 HPE DL560 Gen10 x8 1-port 2 NVMe Slimline Riser Kit” (page 9) “PCIe Slots (Slots 7-8 top to bottom), requires tertiary riser | card and second processor, Not available with 4x Flex Slot power supplies” (page 2)

From the HPE ProLiant DL560 Gen10 Server QuickSpecs (a00008181enw, version 45, 04-December-2023).

All DL560 Gen10 network adapters

The network adapters HPE's QuickSpecs have listed for the DL560 Gen10 across editions, grouped by slot and type. In each group the adapters in stock come first, then the ones our customers order most.

FlexibleLOM or PCIe on the DL560 Gen10?

FlexibleLOMPCIe adapter
How manyOne FlexibleLOM slot, its ports at the rear with port 1 on the right; one FlexibleLOM is chosen from HPE's list of 1Gb to 10/25Gb Ethernet and converged FlexibleLOMs, and HPE also lists an InfiniBand FDR/Ethernet 40/50Gb 547FLR-QSFP adapter.Up to eight PCIe 3.0 slots on three risers
What HPE has listed1GbE to 25GbE Ethernet; InfiniBand and converged adapters1GbE to 25GbE Ethernet; InfiniBand and converged adapters; 16 and 32Gb Fibre Channel HBAs
How to tell from the nameFLR in the name, e.g. 640FLR-SFP28No FLR, e.g. 640SFP28

How to choose a DL560 Gen10 network adapter

Rule 1

Match the cabling to the switch

DAC cables or fiber transceivers and cables are bought separately.

HPE: “Direct Attach Cable (DAC) for copper environments or fiber transceivers and cables for fiber-optic environments must be purchased separately.” (page 38)

Rule 2

Count the processors

Slots 4 to 8 need the second processor.

HPE: “PCIe Slots (Slots 4-6 top to bottom, requires second riser | card and second processor)” (page 2)

Rule 3

Plan the server memory

HPE notes that a minimum of 2 GB of server memory is required per adapter.

HPE: “A minimum of two Gigabytes (2 GB) of server memory is required per each adapter.” (page 38)

Rule 4

Check the cooling

The InfiniBand EDR 100Gb (872726-B21), HDR100 2-port (P06251-B21) and HDR 200Gb (P06154-B21) adapters are each followed by the note that they are not supported in the 24 SFF chassis above 25°C inlet temperature.

HPE: “Notes: Not supported on DL560 Gen10 24SFF chassis when System Inlet Temperature higher than 25°C.” (page 39)

DL560 Gen10 adapter questions

How many network adapters can a DL560 Gen10 take?

The DL560 Gen10 takes network adapters in its one FlexibleLOM slot and in up to eight PCIe 3.0 slots on three risers, of which slots 4 to 8 need the second processor. Three PCIe 3.0 slots as standard and eight with a second processor plus secondary and tertiary riser kits; at most one primary, one secondary and one tertiary riser, and the rear slots are numbered top to bottom, left to right.

Does the DL560 Gen10 have network ports built in?

The CTO server has no network controller of its own: networking comes from a FlexibleLOM adapter in the FlexibleLOM slot or from PCIe NIC cards. Pre-configured models ship with a FlexibleLOM: Entry with the 1Gb 4-port FLR-T I350-T4V2, Base with the FlexFabric 10Gb 2-port FLR-SFP+ 57810S or the 10Gb 2-port FLR-T BCM57416, Performance with the 10/25Gb 2-port FLR-SFP28 MCX4121A-ACFT or BCM57414. Pre-configured models: the Entry and 2-processor Base models have 3 PCIe 3.0 slots (8 with the secondary and tertiary risers), the 4-processor Base models P02874-B21 and P40456-B21 have 6 (8 with the tertiary riser), and the Performance models P02875-B21 and P40457-B21 have 8.

Will an OCP 3.0 adapter fit a DL560 Gen10?

HPE's QuickSpecs for the DL560 Gen10 give it one FlexibleLOM slot: “FlexibleLOM slot (various options can be chosen for networking;” (page 26). The list HPE gives for it has FlexibleLOM adapters for that slot and no OCP 3.0 adapters.

Are cables or transceivers included?

DAC cables or fiber transceivers and cables are bought separately. HPE: “Direct Attach Cable (DAC) for copper environments or fiber transceivers and cables for fiber-optic environments must be purchased separately.” (page 38).

Do I need the second processor for more adapters?

Slots 4 to 8 need the second processor. Slots 1 to 3 run from processor 1. HPE: “PCIe Slots (Slots 4-6 top to bottom, requires second riser | card and second processor)” (page 2).

What do “QuickSpecs version 45” and “earlier HPE edition” mean on the list?

An adapter tagged “Listed in QuickSpecs version 45” is in version 45 of HPE's QuickSpecs for the DL560 Gen10, the edition this page is built from. One tagged “Listed in an earlier HPE edition” was listed for this server in an earlier edition of HPE's QuickSpecs and is not in version 45.

Which Fibre Channel HBAs does HPE list for the DL560 Gen10?

HPE lists Emulex and QLogic Fibre Channel HBAs (16Gb and 32Gb) and two converged network adapters under HPE Storage Options. HPE's QuickSpecs list 8 Fibre Channel HBAs for it, by model: Emulex SN1200E and SN1600E; QLogic SN1100Q and SN1600Q. They are in the Fibre Channel HBAs section of this page.

What if the adapter I need is out of stock?

Out of stock today does not mean unavailable: we can often source this part. Add it to a quote request and we reply with current pricing and availability. Every message, quotes included, is answered within 24 hours.

Most ordered for the DL560 Gen10

The adapters on this page our customers order most, for any server. Each card shows only while the store has it in stock.

FlexibleLOM adapters

12 adapters

One FlexibleLOM slot, its ports at the rear with port 1 on the right; one FlexibleLOM is chosen from HPE's list of 1Gb to 10/25Gb Ethernet and converged FlexibleLOMs, and HPE also lists an InfiniBand FDR/Ethernet 40/50Gb 547FLR-QSFP adapter.

PCIe Ethernet adapters

14 adapters

Stand-up cards for the PCIe slots.

InfiniBand and Omni-Path adapters

7 adapters

HPE lists InfiniBand FDR, EDR, HDR100 and HDR adapters, an Intel Omni-Path 100Gb adapter and the InfiniBand HDR PCIe3 Auxiliary Card kit (P06154-B23) for this server.

Converged network adapters

4 adapters

Adapters HPE names converged network adapters.

Fibre Channel HBAs for the DL560 Gen10

HPE lists Emulex and QLogic Fibre Channel HBAs (16Gb and 32Gb) and two converged network adapters under HPE Storage Options. QuickSpecs page 44

Fibre Channel host bus adapters

8 HBAs
Ships same dayMost orders ship the same business day
1-year warrantyReplacement coverage on every part
5,000+ five-star reviewsShopper Approved, BBB A+ rating
Ships to 120+ countriesBy UPS; duties are collected by the carrier

Equipping several servers?

Send your list as one quote request. Every message, quotes included, is answered within 24 hours.