HPE ProLiant DL585a Gen13 Power Supplies
Genuine HPE power supplies for the HPE ProLiant DL585a Gen13, new and refurbished, shipped tested or factory sealed. The DL585a Gen13 runs on one power supply kit, the HPE 3200W M-CRPS Titanium Hot Plug Power Supply Kit, in two separate power domains: up to two supplies for the system and up to twelve for the GPUs, each domain fully N+N redundant.
DL585a Gen13 Power Supply Specifications
- Kit listed: HPE 3200W M-CRPS Titanium Hot Plug Power Supply Kit, up to 96% efficient; HPE lists no other wattage for this server
- System domain: up to two 3200W M-CRPS supplies
- GPU domain: up to twelve 3200W M-CRPS supplies
- Ordering rule: 10 or 14 power supplies must be selected — 2 for the system domain and 8 or 12 for the GPU domain
- Redundancy: dual power domain configuration, fully N+N redundant
- Rated line voltage: 200 to 240 VAC per power supply; HPE lists no low-line rating for this server
- Power cords: 3200W supplies support C19 and C19-C20 power cords only; cords are not sold on this page
- BTU rating (per 3200W supply): 10,577 BTU/hr at 200 VAC, 11,713 at 220 VAC, 11,699 at 240 VAC
- Form factor: HPE M-CRPS supplies come in 73.5mm and 60mm widths for hot-plug, tool-less installation
One kit, in a count of ten or fourteen. HPE lists a single power supply for the DL585a Gen13, the 3200W M-CRPS Titanium hot-plug kit, and requires 10 or 14 of them: two for the system domain and eight or twelve for the GPU domain, each domain fully N+N redundant. They are rated for 200 to 240 VAC only and take C19 or C19-C20 cords only, so a fully populated server presents fourteen C19 connections to the rack. Size both domains with the HPE Power Advisor before ordering.
How many power supplies does a DL585a Gen13 need?
HPE's rule is simple and strict: ten or fourteen supplies in total. The system domain always takes two; the GPU domain takes eight for the smaller GPU configurations and twelve for the full eight-GPU build. Each domain is N+N, so half of its supplies can fail or lose their feed and the domain keeps running.
| Domain | 3200W supplies | Redundancy | What it powers |
|---|---|---|---|
| System | 2 | N+N | Processors, memory, drives, fans, PCIe slots |
| GPU | 8 or 12 | N+N | The switchboard and up to eight double-wide GPUs |
| Total | 10 or 14 | — | HPE's required selection |
At 3200W per supply and 200 to 240 VAC, a fully populated server presents fourteen C19 connections to the rack. HPE recommends running the HPE Power Advisor before choosing power supplies, and the server's own notes recommend a lift and at least four people for installation.
Choosing the Right DL585a Gen13 Power Supply
- Buy the one kit, in the right count. Every bay in both domains takes the same 3200W M-CRPS Titanium kit; a replacement is the same part whichever domain it serves.
- Plan the rack feed, not just the server. HPE rates these supplies on 200 to 240 VAC only. Fourteen supplies at 3200W is the ceiling the PDUs and the feed have to carry.
- Keep N+N. Running a domain with fewer than its paired count removes the redundancy HPE designs the server around; replace a failed supply with the same kit.
- Cords are C19. HPE lists C19 and C19-C20 cords only for the 3200W supplies; order them per supply.
Complete Your DL585a Gen13 Build
Shop the rest of the server: all DL585a Gen13 parts, processors, memory, E3.S NVMe drives, storage controllers and networking adapters. The same 3200W M-CRPS kit is listed for the DL380a Gen12 and the DL525 Gen13. For other models, browse HPE parts by server model.
DL585a Gen13 Power Supplies FAQ
What power supply does the HPE ProLiant DL585a Gen13 use?
One kit: the HPE 3200W M-CRPS Titanium Hot Plug Power Supply Kit, up to 96% efficient, on 200 to 240 VAC. HPE lists no other wattage for this server. It is used in both power domains, system and GPU.
How many power supplies does the DL585a Gen13 take?
Ten or fourteen. HPE requires 2 power supplies for the system domain and 8 or 12 for the GPU domain, with each domain fully N+N redundant. Up to two supplies serve the system and up to twelve serve the GPUs.
Can I run a DL585a Gen13 on 120V?
HPE rates the DL585a Gen13 power supplies at 200 to 240 VAC and lists no low-line rating for this server. Plan on a 200 to 240 VAC feed with C19 cords.
What power cord does a DL585a Gen13 power supply use?
C19 or C19-C20 cords only, per HPE's note on the 3200W supplies. Power cords are not sold on this page; order one per power supply.
Is the DL585a Gen13 power supply the same as the DL380a Gen12's?
The same part number is listed for both: the HPE 3200W M-CRPS Titanium Hot Plug Power Supply Kit. The DL585a Gen13 is the one that uses it in two separate N+N domains, up to fourteen supplies in total.
✅ Looking for a specific DL585a Gen13 power supply? Browse our full selection below.
Browse all models
Why Global One?
- Trusted by thousands. Over 36,000 customers in 100+ countries trust Global One Technology to deliver mission-critical HP Enterprise hardware - including Fortune 500 businesses, schools, hospitals, and federal, state, and local goverment agencies.
- HPE is our specialty! We only sell genuine HP Enterprise parts.
- EASY ordering process. Purchase online now with credit card or PayPal!
- FAST shipping. Global One Technology ships orders received by 4pm ET the same day and offers NEXT DAY delivery to US customers.
