HP ProLiant DL580 Gen8 Parts

Processors
Fifteen-Core Processors
Twelve-Core Processors
Ten-Core Processors
Eight-Core Processors
Six-Core Processors
NOTE: A minimum of two processors are required. The system may have three or four processors installed.
Back to top
Memory
NOTE: HP memory from previous generation servers are not qualified or warranted with this HP ProLiant Server. HP SmartMemory is required to realize the memory performance improvements and enhanced functionality for Gen8. For additional information, please see the HP SmartMemory QuickSpecs at:http://www8.hp.com/h20195/v2/GetHTML.aspx?docname=c04111165
NOTE: LRDIMM, RDIMM, UDIMM, and HDIMMs are all distinct memory technologies and cannot be mixed within a server. The majority of ProLiant Gen8 servers support LRDIMM, RDIMM and UDIMMs.
Registered DIMMs (RDIMMs)
Load Reduced DIMMs (LRDIMMS)
Memory Expansion Options
NOTE: Up to Eight (8) memory cartridges are supported for 96 DIMM slots
NOTE: A minimum of two memory cartridges are required (one per processor). 
NOTE: A minimum of two memory DIMMs are required per cartridge (minimum of four DIMMs per server).
Back to top
Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.
SAS Hot Plug with Smart Drive SFF (2.5-inch) Enterprise Drives
12G 15K Drives
12G = 12 Gb/sec Transfer Rate Synchronous (Maximum)
15K = 15,000 rpm Rotational Speed
12G 10K Drives
12G = 12 Gb/sec Transfer Rate Synchronous (Maximum)
10K = 10,000 rpm Rotational Speed
6G 15K Drives
6G = 6 Gb/sec Transfer Rate Synchronous (Maximum)
15K = 15,000 rpm Rotational Speed
6G 10K Drives
6G = 6 Gb/sec Transfer Rate Synchronous (Maximum)
10K = 10,000 rpm Rotational Speed
SAS Hot Plug SmartDrive SFF (2.5-inch) Enterprise 512e Drives
SAS Hot Plug SmartDrive SFF (2.5-inch) Midline Drives
NOTE: Please see the QuickSpecs for Technical Specifications and additional information:
6G SATA Value Endurance Hot Plug SFF (2.5-inch) Enterprise Boot Solid State Drives
6G SATA Value Endurance Hot Plug SFF (2.5-inch) Enterprise Value Solid State Drives
6G SATA ME Hot Plug SFF (2.5-inch) Enterprise Mainstream Solid State Drives
6G SATA Hot Plug SFF (2.5-inch) SC MDL HDD
6G SATA VE Hot Plug SFF (2.5-inch) SC EV G1 SSD
6G SATA LE Hot Plug SFF (2.5-inch) SC EL G1 SSD
12G SAS Enterprise Performance and Mainstream Solid State Drives
12G SAS VE SFF (2.5-inch) SC EV Solid State Drives
Hard Drive Option Kits
NOTE: This cable is required when ordering one of these Smart Array Controllers for a PCIe slot.
Back to top
Networking
Gigabit Ethernet Adapters
10 Gigabit Ethernet Adapters
NOTE: A minimum of two Gigabytes (2 GB) of server memory is required per each adapter.
FlexibleLOM Adapters
NOTE: This adapter does not support FCOE Boot from SAN functionality on VMWare and FCOE functionality with RHEL 5.9.
NOTE: Both Legacy and UEFI mode are supported
NOTE: Wake-On-LAN not supported with FlexLOMs on DL580 Gen8
NOTE: Please see the QuickSpecs for Technical Specifications and additional information: www.hp.com/go/ProLiantNICs
Back to top
Power Supplies
NOTE: Prior to making a power supply selection it is highly recommended that the HP Power Advisor is run to determine the right size power supply for your server configuration. The HP Power Advisor is located at:www.hp.com/go/hppoweradvisor.
HP Common Slot Platinum Plus Power Supply Kits
NOTE: 94% efficiency with support for HP Power Discovery Services.
NOTE: All power supplies in a server should match. Mixing Power Supplies is not supported.
NOTE: Option Kits contain specified power supply and PDU IEC cable.
NOTE: 1500W Power Supplies only support High Line Voltage.
NOTE: HP ProLiant servers ship with an IEC-IEC power cord used for rack mounting with Power Distribution Units (PDUs). For a full list of optional HP power cords please go to www.hp.com/products/powercords
Back to top
Graphic Options
NOTE: Up to five cards are supported on the DL580 Gen8. Supporting multiple number of cards on the DL580 Gen8 blocks some active IO cards as follows due to space constraints:
For 2P config: Max of 2 double-wide cards are supported on slot 6 and slot 9 (slot 8 is blocked)
For 3P config: Max of 3 double-wide cards are supported on slot 3, slot 6 and slot 9 (slot 5 and slot 8 are blocked)
For 4P config: Max of 5 double wide cards are supported on Slot 1, Slot 3, Slot 2, Slot 6 and Slot 9 (slot 5 and slot 8 are blocked).
NOTE: HP DL580/DL585/DL980 Power Cable Kit (631660-B21) is required for Graphics cards. Each cable kit has two 8-pin connectors (one 150W and other 225W) and can support up to two cards. For three cards, two cable kits are required. For five cards, three cable kits are required. The cards pull up to 75W of power from the IO slot and the rest from the auxiliary power connectors.
NOTE: Both UEFI mode and Legacy Mode are supported.
NOTE: Supported at Gen2 speeds
NOTE: Supported at Gen2 speeds
Back to top
Storage Controllers
SAS Controllers
Smart Array P430 Controller
Smart Array P431 Controller
Smart Array P830 Controller
Optional Upgrades
NOTE: A maximum of four HP Smart Array Controllers (including embedded controller) can be installed 
NOTE: For more information about HP SmartCache, go towww.hp.com/go/smartcache
NOTE: Both Legacy and UEFI modes are supported
NOTE: Please see the QuickSpecs for Technical Specifications and additional information: 
Back to top
Tape Backup
NOTE: For the complete range of tape drives, autoloaders, libraries and media see:http://www.hp.com/go/tape. For hardware and software compatibility of HP tape backup products see: https://h20272.www2.hp.com/spock/ and www.hp.com/go/ebs.
NOTE: For Internal drives to be connected to DL servers please make sure that you order rack mount kit as well.
Back to top
Tape Storage Systems
HP StoreEver MSL6480
NOTE: Please see the QuickSpecs for Technical Specifications and additional information:
Back to top
Disk Backup
NOTE: For the complete range of RDX drives and media see:http://www.hp.com/go/rdx. For hardware and software compatibility of HP disk backup products see: https://h20272.www2.hp.com/spock/. 
NOTE: For Internal drives to be connected to DL servers please make sure that you order rack mount kit as well.
Back to top
Disk Storage  Systems
Disk Enclosures
NOTE: Please see the QuickSpecs for Technical Specifications and additional information:
Back to top
Infiniband Options
NOTE: UEFI and Legacy modes are supported with Ethernet and Infiniband functionality.
NOTE: UEFI and Legacy modes are supported with Ethernet and Infiniband functionality.
NOTE: Legacy and UEFI modes are supported
Back to top
Storage Options
Storage Fibre Channel HBA 
NOTE: The following is a list of all Fibre Channel Host Bus Adapters for Windows and Linux. For detailed compatibility information please see:http://h18006.www1.hp.com/storage/saninfrastructure/hba.html
QLogic Fibre Channel HBAs
Emulex Fibre Channel HBAs
NOTE: Both Legacy and UEFI mode is supported.
Back to top
Rack Options
HP Location Discovery Services
HP TFT7600 G2 KVM Console and Monitor (TFT7600 G2)
NOTE: Please see the QuickSpecs for Technical Specifications and additional information:
HP Server Console Switches
NOTE: Please see the QuickSpecs for Technical Specifications and additional information:
HP Server Console Switch G2 with Virtual Media & CAC
NOTE: Please see the QuickSpecs for Technical Specifications and additional information:
HP IP Console Switch G2 with Virtual Media & CAC
NOTE: Please see the QuickSpecs for Technical Specifications and additional information:
Back to top
USB and SD Options
HP Flash Media Kits for USB Drives
HP Enterprise Mainstream Flash Media Kits for Memory Cards
NOTE: Please see the QuickSpecs for additional information:
Back to top

Last updated: 12/10/2018

Need help finding the correct part? Live Chat operators are standing by. LET US HELP