HPE ProLiant BL465c Gen8 Parts

HPE ProLiant BL465c Gen8 Parts

HPE ProLiant BL465c Gen8 Parts

Networking

10Gb Ethernet Mezzanine 

NOTE:  Each 10 Gigabit Ethernet adapter requires a minimum of 2GB of server memory.
NOTE:  A 10 Gigabit Ethernet adapter supports linking at 1Gbps or 10Gbps when connected to an interconnect module with 10Gb Ethernet downlinks. 
NOTE:  A 10 Gigabit Ethernet adapter supports linking at only 1Gbps when connected to an interconnect module with 1Gb Ethernet downlinks. 
NOTE:  The 10 Gigabit Ethernet adapters on each server blade connect to a 10Gb interconnect in bays 3-8 (HPE BladeSystem c7000 Enclosure) or bays 2-4 (HPE BladeSystem c3000 Enclosure).

1Gb Ethernet Mezzanine

FlexibleLOM Adapters

NOTE:  The server supports one FlexibleLOM that is installed in the FlexibleLOM connector and is already included in Pre-configured Models and added per Step 2 for Factory Integrated Models. The FlexibleLOM options below are used to change these original FlexibleLOMs.

10Gb FlexibleLOM

Memory

NOTE:  To realize the performance memory capabilities for this server, HPE SmartMemory is required. For additional information, please see the HPE SmartMemory QuickSpecs at:
NOTE:  HPE memory from previous generation servers are not fully compatible with Smart Memory features in Gen8 Servers.
NOTE:  A minimum of one DIMM is required per server.
NOTE:  For additional memory rules and guidelines, see the "Memory" section of the Quickspecs document for this server.

HPE SmartMemory

Registered DIMMs (RDIMMs)

Load Reduced DIMMs (LRDIMMs)

Ultra Low Voltage DIMMs (ULVDIMM) for AMD Servers

Drives

NOTE:  The ProLiant BL465c Gen8 server includes the new HPE hot-plug small form factor (SFF) SmartDrive carrier for enhanced management and reduced maintenance errors. HPE drives from previous generation servers are not compatible with the BL465c Gen8 drive bays.
NOTE:  The mixing of standard SAS drives with SAS SSD drives is supported within the server, but limits the RAID configuration to two separate RAID 0 volumes. Mixing of other drives types is not supported.
NOTE:  The hard drive options are not required when configuring a drive-less model.
NOTE:  Server supports only 3G SATA devices. The 6G SATA drives will negotiate to 3G speeds.

6G SATA Hot Plug with SmartDrive SFF (2.5-inch) Midline (MDL) Drives

SAS Hot Plug with Smart Drive SFF (2.5-inch) Enterprise Drives

12G 15K Drives

12G 10K Drives

6G 15K Drives

6G 10K Drives

SAS Hot Plug SmartDrive SFF (2.5-inch) Enterprise 512e Drives

SAS Hot Plug SmartDrive SFF (2.5-inch) Midline Drives

6G SAS ME Hot Plug SFF (2.5-inch) Enterprise Mainstream Solid State Drive

3G SATA MLC Hot Plug SFF (2.5-inch) Enterprise Mainstream Solid State Drives

HPE 100GB 3G SATA MLC SFF (2.5-inch) SC Enterprise Mainstream Solid State Drive thumb
NOTE:  Servers supports only 3G SATA drives. The 6G SATA drives will negotiate to 3G speeds.
NOTE:  The mixing of standard SAS drives with SAS SSD drives is supported within the server, but limits the RAID configuration to two separate RAID 0 volumes. Mixing of other drives types is not supported.
$399
$281.00

6G SAS SLC Hot Plug SFF (2.5-inch) Enterprise Performance Solid State Drives

InfiniBand Mezzanines

NOTE:  When an InfiniBand adapter is installed in mezzanine slot 1, only one port is active (regardless of operating mode). When installed in any other mezzanine slot, both ports are active.
NOTE:  On PCIe Gen2 based servers like BL465 Gen8, InfiniBand FDR speeds are not feasible.
HPE QDR/EN InfiniBand 10Gb Dual Port 544M Adapter thumb
NOTE:  The QDR InfiniBand adapter may be installed in any mezzanine slot of the server.
$91
$65.00
HPE FDR/EN InfiniBand 10/40Gb Dual Port 544M Adapter thumb
NOTE:  The FDR InfiniBand adapter must be installed in mezzanine slot 1 for FDR mode and may be installed in any mezzanine slot if operated in any other mode.
$210
$158.00

Ultrium Tape Blades

HPE LTO-4 SB1760c Tape Blade thumb
NOTE:  LTO-4 Ultrium tape technology.
HPE LTO-5 SB3000c Tape Blade thumb
NOTE:  LTO-5 Ultrium tape technology.
$7,222
$6,500.00

Storage Blades

Expansion Blade

HPE BLc PCI Expansion Blade thumb
NOTE:  The PCI Expansion Blade provides PCI card slots for an adjacent c-Class Server Blade. Order one PCI expansion Blade for each server blade needing standard PCI-X or PCIe expansion slots. 
NOTE:  Ships with one pre-installed PCI-X connect board. Also includes one PCIe connect board which requires installation.
$359
$246.00

Processors

NOTE: HPE server processor pricing is volatile and availability is unpredictable. Please select any CPU kit below and click Request Quote and submit the form to get the current pricing for that CPU kit.
NOTE: All CPU Kits come complete with heatsink, fan(s), etc
NOTE: The BL465c Gen8 supports one or two processors.
NOTE: All processors within the server must be identical.
NOTE: The letters HE following the model number denotes lower wattage.
NOTE: The memory configuration determines the maximum speed memory can operate. Please see the see the Memory section later in this document.

Sixteen-Core Processors

Twelve-Core Processors

Eight-Core Processors

Quad-Core Processors

Compare Selected