HPE ProLiant BL465c G7 Parts
Ethernet Mezzanine Options
Gigabit Ethernet Mezzanines
NOTE: If the NC325m is installed in mezzanine slot 1 of a half-height server, connectivity will be provided on only 2 of the 4 ports.
$76
$56.00
$91
$72.00
NOTE: If the NC364m is installed in mezzanine slot 1 of a half-height server, connectivity will be provided on only 2 of the 4 ports.
$81
$60.00
10 Gigabit Ethernet Mezzanines
NOTE: The NC532m requires a minimum of 2 GB of server memory.
NOTE: The NC532m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 enabled module and will link with all current 1Gb switches at 1Gb.
$146
$98.00
NOTE: The NC542m requires a minimum of 2 GB of server memory.
NOTE: The NC542m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 device. The NC542m will only support 1000Mbps when connected to a 1Gb Ethernet interconnect.
$64
$49.00
NOTE: The NC550m network adapter card is required for each server blade connecting to a 10Gb interconnect in bays 3-8 (HPE BladeSystem c7000 Enclosure) or bays 3-4 (HPE BladeSystem c3000 Enclosure)
NOTE: The NC550m requires a minimum of 2 GB of server memory.
NOTE: The NC550m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 device. The NC550m will only support 1000Mbps when connected to a 1Gb Ethernet interconnect.
$320
$218.00
NOTE: The NC551m network adapter card is required for each server blade connecting to a 10Gb interconnect in bays 3-8 (HPE BladeSystem c7000 Enclosure) or bays 3-4 (HPE BladeSystem c3000 Enclosure)
NOTE: The NC551m requires a minimum of 2 GB of server memory.
NOTE: The NC551m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 device. The NC551m supports 1000Mbps when connected to a 1Gb Ethernet interconnect.
$97
$77.00
NOTE: A 10 Gigabit Ethernet adapter is required for each server blade connecting to a 10Gb interconnect in bays 3-8 (HPE BladeSystem c7000 Enclosure) or bays 2-4 (HPE BladeSystem c3000 Enclosure).
NOTE: Each 10 Gigabit Ethernet adapter requires a minimum of 2GB of server memory.
NOTE: A 10 Gigabit Ethernet adapter will down speed to 1Gb if paired with a 1GbE interconnect.
NOTE: HPE recommends 10Gb adapters be installed in a x8 PCIe slot for optimal performance.
NOTE: The ROM Based Setup Utility (RBSU) feature allows for the configuring of a FlexFabric Adapter to any of the supported protocols. For example iSCSI to FCoE (Fibre Channel over Ethernet). Note that a HPE Virtual Connect profile takes precedence over the setting in this menu. Also, some FlexFabric Adapters may require that network boot be enabled in order to configure the protocol. If the protocol is configured without enabling network boot with certain FlexFabric Adapters, the protocol may not take effect. Once the protocol has taken effect on the first boot after configuring this option, network boot may be disabled if desired.
Fibre Channel Mezzanine Options
4Gb Fibre Channel Mezzanines
8Gb Fibre Channel Mezzanines
Memory
Registered DIMMs (RDIMMs)
$66
$49.00
$81
$56.00
$95
$77.00
$68
$49.00
$94
$76.00
Unbuffered with ECC DIMMs (UDIMMs)
$83
$67.00
$243
$219.00
NOTE: A minimum of one (1) DIMM per processor is required.
NOTE: Each processor memory bus will operate at up to 1333 MHz with either one quad-rank (QR) or two single-rank/dual-rank (SR/DR) DIMMs per processor memory channel and 1066 MHz with up to two QR or one QR and one SR/DR DIMMs per processor memory channel with standard voltage (1.5V, PC3) DIMMs. Memory bus will operate one speed slower when low voltage (1.35V, PC3L) memory is installed. Memory bus speeds may be further limited by the speed of the memory used as well.
Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.
SAS Hot Plug 2.5" SFF Enterprise (ENT) Drives
12G 15K Drives
12G = 12 Gb/sec Transfer Rate Synchronous (Maximum)
15K = 15,000 rpm Rotational Speed
12G 10K Drives 
12G = 12 Gb/sec Transfer Rate Synchronous (Maximum)
10K = 10,000 rpm Rotational Speed
6G 15K Drives
6G = 6 Gb/sec Transfer Rate Synchronous (Maximum)
15K = 15,000 rpm Rotational Speed
6G 10K Drives
6G = 6 Gb/sec Transfer Rate Synchronous (Maximum)
10K = 10,000 rpm Rotational Speed
3G 15K Drives
3G = 3 Gb/sec Transfer Rate Synchronous (Maximum)
15K = 15,000 rpm Rotational Speed
3G 10K Drives
3G = 3 Gb/sec Transfer Rate Synchronous (Maximum)
10K = 10,000 rpm Rotational Speed
NOTE: Please see the SAS Hard Drive QuickSpecs for Technical Specifications such as capacity, height, width, interface, transfer rate, seek time, physical configuration, and operating temperature:
SAS Hot Plug 2.5" SFF Midline (MDL) Drives
$133
$95.00
$186
$128.00
SATA Hot Plug 2.5" SFF Midline (MDL) Drives
$144
$98.00
$83
$58.00
$288
$220.00
SATA Hot Plug 2.5" Midline (MDL) Solid State Drives
Storage Controllers
NOTE: Supports all HPE ProLiant Server Blades, except the HPE ProLiant BL2x220c and BL685c G7 server blades.
Optional Upgrades
NOTE: The BL465c G7 supports a maximum of one array controller battery. If one Smart Array P700m controller with cache battery kit is ordered for factory integration, the internal Smart Array P410i cache module capacitor will be removed and shipped with the server for customer installation.
$86
$68.00
I/O Expansion Options
InfiniBand Mezzanine Options
Ultrium Tape Blades
NOTE: LTO-4 Ultrium technology
$3,987
$3,588.00
NOTE: LTO-3 Ultrium technology
$2,772
$2,495.00
StorageWorks SB40c Storage Blade
$495
$385.00
Expansion Blade
$359
$246.00
NOTE: Ships with one pre-installed PCI-X connect board. Also includes one PCIe connect board which requires installation.
Processors
| NOTE: HPE server processor pricing is volatile and availability is unpredictable. Please select any CPU kit below and click Request Quote and submit the form to get the current pricing for that CPU kit. |
NOTE: All CPU Kits come complete with heatsink, fan(s), etc
Twelve-Core Processors
Eight-Core Processors
NOTE: HPE ProLiant BL465c G7 processor option kits contain one (1) processor.
Why Global One?
- Trusted by thousands. Over 32,000 customers in 100+ countries trust Global One Technology to deliver mission-critical HP Enterprise hardware - including Fortune 500 businesses, schools, hospitals, and federal, state, and local goverment agencies.
- HPE is our specialty! We only sell genuine HP Enterprise parts.
- EASY ordering process. Purchase online now with credit card or PayPal!
- FAST shipping. Global One Technology ships orders received by 5pm the same day and offers NEXT DAY delivery to US customers.
