P667 Pentium III 256K Processor Option Kit Note: This option kit is made available for those customers that have purchased a ProLiant ML350 667 MHz (667-MHz models are only available directly or configured through the Web from Compaq). Note: This processor option kit (PN 159756-B21) supports the ProLiant ML350 (1st generation), and ProLiant ML370 servers.
NOTE: All U320 Universal Hard Drives are backward compatible to U2 or U3 speeds. U320 drives require an optional U320 Smart Array Controller or U320 SCSI HBA to support U320 transfer rates.
NOTE: Please see the Hard Drive QuickSpecs for Technical Specifications such as capacity, height, width, interface, transfer rate, seek time, physical configuration, and operating temperature.
Note: Wide Ultra3 Drives require an optional Wide Ultra3 Controller to support Ultra3 transfer rates.
Note: When upgrading a Non-Hot Plug Model to Hot Plug, the purchase of the Hot Plug Drive Cage Upgrade Option Kit (161275-B21) is required to support hot plug (Ultra2/Ultra3) hard drives.
Note: When upgrading a Non-Hot Plug Model to Hot Plug, the purchase of the Hot Plug Drive Cage Upgrade Option Kit (161275-B21) is required to support hot plug (Ultra2/Ultra3) hard drives.
Pentium III P1133-512KB (FC-PGA2) Processor Option Kit Note: This processor option kit (PN 238888-B21) supports the ProLiant ML350 Generation 2 (G2), and ProLiant ML370 Generation 2 (G2) servers. It includes a heatsink and VRM.
Note: All U320 Universal Hard Drives are backward compatible to U2 or U3 speeds and will run at U3 within the ML350 G2.
Note: Please see the Hard Drive QuickSpecs for Technical Specifications such as capacity, height, width, interface, transfer rate, seek time, physical configuration, and operating temperature: U320 Hard Drive Quickspecs http://www5.compaq.com/products/quickspecs/11531_na/11531_na.HTML
256-MB Battery-Back Cache Module Note: This 256-MB Battery-Backed Cache Module supports the Smart Array 5300 series controllers, MSA 1000 and the Smart Array Cluster Storage.
Intel Xeon 2.8 GHz-1MB Processor Option Kit NOTE: The 2.8 GHz-1MB processor option kit (PN 352567-B21) supports ProLiant ML350 G3 systems with 533 MHz front side bus only. This kit cannot be used in 400 MHz front side bus systems such as those with 2.4 GHz, 2.2 GHz or 2.0 GHz processors.
Intel Xeon 3.06 GHz-512KB Processor Option Kit NOTE: The 3.06 GHz processor option kit (PN 257916-B21) supports ProLiant ML350 G3 systems with 533 MHz front side bus only. This kit cannot be used in 400 MHz front side bus systems such as those with 2.4 GHz, 2.2 GHz or 2.0 GHz processors.
Intel Xeon 2.8 GHz-512KB Processor Option Kit NOTE: The 2.8 GHz processor option kit (PN 314763-B21) supports ProLiant ML350 G3 systems with 533 MHz front side bus only. This kit cannot be used in 400 MHz front side bus systems such as those with 2.4 GHz, 2.2 GHz or 2.0 GHz processors.
Intel Xeon 2.4 GHz-512KB Processor Option Kit NOTE: This processor option kit supports ProLiant ML350/ML370/DL380 G3 servers with 400 MHz front side bus only. This kit (PN 257913-B21) cannot be used in 533 MHz front side bus systems such as the 2.8 GHz systems.
NOTE: The ML350 G3 supports both interleaved and non-interleaved memory configurations. For best performance automatically invoke interleaving by populating memory in identical pairs. If 1GB of total memory is desired add one 512 MB DIMM to the base confi
NOTE: Each SDRAM Memory kit contains one (1) DIMM.
NOTE: All U320 Universal Hard Drives are backward compatible to U2 or U3 speeds. U320 drives require an optional U320 Smart Array Controller or U320 SCSI HBA to support U320 transfer rates.
256-MB Battery Backed Cache Module NOTE: This 256-MB Battery Backed Cache Module supports the Smart Array 5300 series controllers, HP StorageWorks Modular Smart Array 1000 and the HP StorageWorks Modular Smart Array 500.
NOTE: The HP ProLiant ML350 G4 requires interleaved memory configurations when more than one DIMM is installed. Base models ship standard with a single DIMM. To upgrade system memory, DIMMs must be installed in identical pairs.
NOTE: Each SDRAM Memory kit contains one (1) DIMM.
NOTE: A minimum of 1 GB of memory per port is required for NC370x adapters, with a maximum of two NC370x ports permitted in a server.
NOTE: NC61XX, NC71XX, NC77XX, or NC1020 network adapter (NIC) can be used for redundancy with the embedded NC7761 NIC. When either the embedded NC7761 or the NC1020 is teamed with other HP Ethernet adapters, Jumbo Frames and LSO features are automatically
NOTE: All U320 Universal Hard Drives are backward compatible to U2 or U3 speeds. U320 drives require an optional U320 Smart Array Controller or U320 SCSI HBA to support U320 transfer rates.
HP PCI-X Expander Kit (2 x 64-bit 100MHz PCI-X slots) NOTE: The HP PCI-X Expander kit converts a single PCI Express slot (slot 6) into two full height, full length 64-bit 100MHz PCI-X slots. NOTE: The HP PCI-X Expander kit can support a maximum of one (1) HP Smart array, HBA, or SCSI PCI-X adapter. Prioritize internal slots for use with PCI-X storage controllers. Please refer to the ML350G5 user guide for additional details.
NOTE: Please note that some of the earlier BTO models may not support adding SATA Optical Drives. To ensure compatibility of the SATA Optical Drives, please add additional optical drives only on models with Quad-Core 5400 Series processors.
Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.
NOTE: Please note that SFF 2.5" (small form factor) drives can only be installed on tower or rack models with SFF chassis (models).
NOTE: Please note that LFF 3.5" (large form factor) drives can only be installed on tower or rack models with LFF chassis (models).
HP NC522SFP Dual Port 10GbE Server Adapter NOTE: A minimum of two gigabyte (2 GB) of server memory is required per each NC522SFP adapter. NOTE: Direct Attach Cable (DAC) for copper environments or fiber transceivers and cables for fiber-optic environments must be purchased separately.
HP SA-P400 and SA-E500 24 In Battery Cable Kit NOTE: This option kit contains a 24" battery cable and adhesive material for installing a battery into the server if a Smart Array P400 is integrated outside of the factory. For all solutions, please refer to the server QuickSpecs and User's Manual for detailed installation instructions.
HP x4-x8 PCI-E Bus Expander Option Kit NOTE: The HP x4/x8 PCI Express Bus Expander kit converts 2 x4 PCI Express slots into a single x8 PCI Express slot for high performance x8 PCI Express cards.
HP ML350 G6 2 Slot PCI-X Riser Kit NOTE: The HP PCI-X Expander kit converts a single PCI Express slot (slot 6) into two full height, full length 64-bit 100MHz PCI-X slots.
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed memory configuration rules and guidelines, please use the Online DDR3 Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator.
NOTE: Kits described as LP include Low Power DIMMs. For more information on ProLiant Energy Efficient Features, see: www.hp.com/go/proliant-energy-efficient.
NOTE: Please note that some of the earlier BTO models may not support adding SATA Optical Drives. To ensure compatibility of the SATA Optical Drives, please add additional optical drives only on models with Quad-Core 5400 Series.
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.
HP NC364T PCI-E Quad Port Gigabit Server Adapter NOTE: Does not support Windows 2000. NOTE: There is a maximum of five NC364T PCI Express Quad Port Gigabit Server Adapter NICs allowed in this server.
NOTE: Direct Attach Cable (DAC) for copper environments or fiber transceivers and cables for fiber-optic environments must be purchased separately.
NOTE: Please see the QuickSpecs for Technical Specifications and additional information: www.hp.com/go/ProLiantNICs
Redundant Options
CAUTION: Optional Power Supplies used for Redundancy "must" match the original supplied power supply. Upgrades for more power headroom, when replacing the original power supplies must match if purchased for redundancy. Option Kits contain optional power supply, an IEC power cable and PDU IEC cables. In ProLiant Servers that have more than one power slot (bay), only same size power supplies are recommended. If non-matched power supplies are inserted you will get errors and operation will fail.
NOTE: Option Kits contain optional power supply, an IEC power cable and PDU IEC cables.
NOTE: Prior to making a power supply selection it is "highly recommended" that the "HP Power Advisor" is run to determine the right size power supply for your server configuration. www.hp.com/go/proliant-energy-efficient
NOTE: While ordering the 256 BBWC (462968-B21) or the 512 BBWC (462967-B21) kits on the Smart Array controllers the customer also needs to order a 24 inch SFP Battery Cable (496029-B21)
