| Ethernet Mezzanine Options | |
|
HP NC325m PCI Express Quad Port Gigabit Server Adapter
NOTE: If the NC325m is installed in mezzanine slot 1 of a half-height server, connectivity will be provided on 2 of the 4 ports. | |
HP NC364m Quad Port 1GbE BL-c Adapter
NOTE: If the NC364m is installed in mezzanine slot 1 of a half-height server, connectivity will be provided on only 2 of the 4 ports. | |
| HP NC382m PCI Express Dual Port Multifunction Gigabit Server Adapter | |
| HP BLc QLogic iSCSI Dual Port Adapter | |
| NOTE: The Gigabit Ethernet adapters above transmit from the server at 2000 Mbps, full duplex per port only. For more information, see the "Network Controller" segment in the Standards Features section. |
|
HP NC522m Dual Port 10GbE Multifunction BL-c Adapter
NOTE: The NC522m network adapter card is required for each server blade connecting to a 10Gb interconnect in bays 3-8 (HP BladeSystem c7000 Enclosure) or bays 3-4 (HP BladeSystem c3000 Enclosure).
NOTE: The NC522m requires a minimum of 2 GB of server memory.
NOTE: The NC522m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 enabled module and will link with all current 1Gb switches at 1Gb. | |
HP NC532m Dual Port 10GbE BL-c Adapter
NOTE: The NC532m network adapter card is required for each server blade connecting to a 10Gb interconnect in bays 3-8 (HP BladeSystem c7000 Enclosure) or bays 2-4 (HP BladeSystem c3000 Enclosure).
NOTE: The NC532m requires a minimum of 2 GB of server memory.
NOTE: The NC532m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 enabled module and will link with all current 1Gb switches at 1Gb. | |
HP NC542m Dual Port Flex-10 10GbE Multifunction BL-c Adapter
NOTE: The NC542m network adapter card is required for each server blade connecting to a 10Gb interconnect in bays 3-8 (HP BladeSystem c7000 Enclosure) or bays 3-4 (HP BladeSystem c3000 Enclosure).
NOTE: The NC542m requires a minimum of 2 GB of server memory.
NOTE: The NC542m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 device. The NC542m will only support 1000Mbps when connected to a 1Gb Ethernet interconnect. | |
HP NC550m 10GbE 2-port PCIe x8 Flex-10 Ethernet Adapter
NOTE: The NC550m network adapter card is required for each server blade connecting to a 10Gb interconnect in bays 3-8 (HP BladeSystem c7000 Enclosure) or bays 2-4 (HP BladeSystem c3000 Enclosure).
NOTE: The NC550m requires a minimum of 2 GB of server memory.
NOTE: The NC550m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 device. The NC550m will only support 1000Mbps when connected to a 1Gb Ethernet interconnect. | |
HP BLc NC552m Flex-10GbE Dual Port Adapter
NOTE: The NC552m network adapter card is required for each server blade connecting to a 10Gb interconnect in bays 3-8 (HP BladeSystem c7000 Enclosure) or bays 2-4 (HP BladeSystem c3000 Enclosure).
NOTE: The NC552m requires a minimum of 2 GB of server memory.
NOTE: The NC552m supports linking at 1000Mbps or 10000Mbps when not connected to a Flex-10 device. The NC552m will only support 1000Mbps when connected to a 1Gb Ethernet interconnect. | |
| NOTE: The ROM Based Setup Utility (RBSU) feature allows for the configuring of a FlexFabric Adapter to any of the supported protocols. For example iSCSI to FCoE (Fibre Channel over Ethernet). Note that a HP Virtual Connect profile takes precedence over the setting in this menu. Also, some FlexFabric Adapters may require that network boot be enabled in order to configure the protocol. If the protocol is configured without enabling network boot with certain FlexFabric Adapters, the protocol may not take effect. Once the protocol has taken effect on the first boot after configuring this option, network boot may be disabled if desired. |
|
